background image

SM-100 CERTISAFE™ SUSPENDED MOUNT

MANUAL

852112 / 2021.1.1

13

CERTISAFE™ TANK MIXER WARRANTY

Kasco offers a standard 3-year warranty with the following 

models:

•  2400C61

• 

3400C61 / 3400HC61

• 

4400C61 / 4400HC61

• 

8400C61

At the time of purchase, a 5-year warranty is available for pack-

ages including Advanced model control panels.

Warranty must be purchased at the same time as the mixer 

package. (Mixer package consists of the mixer, mount, and 

control panel.)

Control panel MUST have GFCI protection.

Kasco® Marine, Inc. warrants this CertiSafe™ mixing system to 

be free from defects in material or workmanship under appro-

priate use and service. The Kasco Marine, Inc. obligation under 

this warranty is limited to replacing or repairing, without charge, 

proven defective part while within the warranty period. Customer 

shall pay shipping charges for returning the unit to Kasco.

Note: 

Kasco only

 

accepts complete assemblies for warranty repair. We must receive the power cord and all other components 

with the motor as originally assembled. Kasco will bill the customer to replace any missing parts necessary for repair. It is not 

necessary to return the control panel, mount, or other parts with the motor assembly, unless specifically requested by a Kasco 

representative.

Please attach a repair form with the shipment. The repair form must include a name, physical address (for return delivery of the 

repaired unit), daytime phone number, and an e-mail address for correspondence regarding the warranty claim.

Any expedited shipping method for the return of the unit is at the customer’s expense. Kasco Marine will return units repaired 

under warranty at our expense via ground freight within the continental United States.

Shipping Address: 

Kasco Marine, Inc.

800 Deere Rd.

Prescott, WI 54021

Attn: Repairs

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, 

EXPRESSED OR IMPLIED. IN NO EVENT WILL KASCO 

MARINE, INC. BE LIABLE FOR ANY CONSEQUENTIAL 

DAMAGES.

Warranty is void if:

•  The mixer is not maintained according to the recommenda-

tions supplied in this manual.

•  The mixer is returned for repair without the power cord.

•  The unit, control box, or power cord are altered in any way 

from original shipment.

•  The power cord is nicked or cut.

•  The mixer is damaged by unauthorized service.

Warranty Claim Procedure

Warranty period is established by the original receipt. For efficient service, please register the unit online at: 

www.kascomarine.com/warranty-registration

.

Once warranty coverage has been established, you may send the unit to Kasco for evaluation and repair.

Back to Contents

Содержание CertiSafe
















Отзывы: