background image

 
 
 

 
 

800 Deere Rd. 

Prescott, WI 54021 

Phone: 715-262-4488  -  Fax: 715-262-4487 

www.De-Icer.com     [email protected] 

 

Kasco Repair Sheet — Customer Info. 

 

* Important Reminders * 

• 

All repairs sent in MUST be accompanied by a copy of this completed sheet! 

• 

Routine maintenance consists of checking the zinc anode regularly and replacing if necessary, keeping the 
unit clean, keeping the stainless steel can clean, and having the seals and oil replaced every 3-5 years de-
pending on use. 

• 

Address your Repair to Kasco Marine, Attn: Repairs (or to your Authorized Repair Center). 

• 

Shipping to Kasco or an Authorized Repair Center is paid for by the customer. 

• 

You must include the power cord and cage assembly with each unit sent in for repair to be considered for 
warranty repair! 

• 

Do not ship the float and/or control box with the unit for repair, unless otherwise instructed. 

 
Today’s Date:___________________ 

 

Customer Information 

 

Name: 

_________________ 

    Phone 

Number: 

_____________________ 

 

Address: __________________________ 

 

 

Alternate Number: ___________________ 

 

City: 

____________________    Email 

Address: 

______________________ 

 

State: _____________________ 

 

Zip Code: ______________________ 
 

Unit Information: 

 

Model # (Ex. 3400D): ____________________ 

 

Serial # (Ex. 6001D34025): ____________________ 

 

Date Purchased: ________________________ 

 

Purchased From: _________________________ 

 

Earliest Date of Problem: _______________________ 
 
Description of Problem 
 
 
 
 
 
Comments 

 

 

21 

Содержание C10























Отзывы: