background image

23

Warranty Policy

3 Year Limited Warranty: Kasco® Marine, Inc. war-
rants this aerator to be free from defects in material or 
workmanship (except for the ropes, power cord, and 
propeller) under normal use and service.  The Kasco 
Marine, Inc. obligation under this warranty is limited 
to replacing or repairing free of charge any defective 
part within three (3) years from the date of shipment.  
Customer shall pay shipping charges for returning the 
unit to Kasco or an Authorized Repair Center.

THIS WARRANTY IS IN LIEU OF ANY OTHER 
WARRANTIES, EXPRESSED OR IMPLIED, AND 
ANY OTHER OBLIGATION OR LIABILITY 
WHATEVER ON THE PART OF KASCO MARINE, 
INC. AND IN NO EVENT SHALL KASCO 
MARINE, INC. BE LIABLE FOR ANY SPECIAL 
OR CONSEQUENTIAL DAMAGES.

Warranty is void if:
•  The aerator is not maintained properly according 

to the Maintenance Recommendations supplied in 
this Owners Manual.

•  The aerator is returned for repair without the 

power cord or if the unit, control box, or power 
cord are altered in any way from original ship-
ment.  Cuts in the power cord are not covered 
under warranty.

•  The aerator is not used with the supplied GFI con-

trol box.

•  The aerator is damaged by unauthorized tamper-

ing.

• 

The Sacrificial Zinc Anode around the propeller 

shaft shows significant deterioration.  (The Anode 

must be inspected periodically and replaced if 
necessary.)

Warranty Claim Procedure:
The best method for establishing warranty period is by 
the original receipt.  Also, register the aerator online 
at:  www.kascomarine.com

Once the warranty coverage has been established, the 
unit may be sent to any Kasco Authorized Repair Cen-
ter for evaluation and repair.  Please call Kasco Ma-
rine at 715-262-4488 prior to shipping to receive any 
updated information and/or Repair Form, then ship to:

Kasco Marine, Inc.
800 Deere Rd.
Prescott, WI 54021
Attn: Repairs

Or call Kasco Marine at 715-262-4488 to locate your 
nearest Authorized Repair Center.  You can also email 
Kasco at [email protected]
Note:  Only complete motor assemblies will be ac-
cepted for warranty repair.  The power cord and all 
other components must be returned with the motor as 
originally assembled.  Any missing parts will be re-
placed at the customer’s expense and, if determined to 
have caused the failure, could void the entire warranty.  
Some parts are essential for structural support during 
shipping and others, such as the power cord, are es-
sential to properly diagnose potential causes of failure.  

It is not necessary to return the control box, float, or 

nozzles with the motor assembly, unless specifically 

asked to by a Kasco representative. 

Please include the Repair Form received from Kasco 
Marine or your local distributor with the shipment.  If 
no Repair Form is available, include your name and 
physical address for return delivery of the repaired 
unit and a daytime phone number and/or e-mail ad-
dress for correspondence regarding the warranty 
claim.

Any expedited shipping method for the return of the 
unit is at the customer’s expense.  Kasco Marine will 
return units repaired under warranty at our expense via 
ground freight within the continental United States.
Other Repairs:

Most failed equipment can be repaired at substantially 
lower costs than replacement with new.  Please ship 
according to the instructions in the previous section.  
Again, it is best to call ahead for updated information 
and/or Repair Form.

Kasco Marine does estimates on repairs at the request 
of the customer.  The request for estimate should be 
included in the letter that accompanies the returned 
unit and must include a daytime phone number and/or 
e-mail address.  Estimate options are as follows:

We will contact the customer with a total after the unit 
has been evaluated, but before the work is performed.
We will repair the unit only if repair costs are under a 
stated dollar amount.  Example: “Please repair if total 
is under $150.00 before shipping charges.”

All estimates that are rejected for repair will be 
destroyed unless otherwise directed by the customer.  
If the customer would like the unit returned, the unit 
will be restored as closely as possible to the condition 
in which it was received and shipped at the customer’s 

Содержание 3.1JF





























Отзывы: