Kasco Aeration 3400HJF Скачать руководство пользователя страница 18

18

Troubleshooting Tips

Below are some helpful troubleshooting tips.  If a 
problem occurs, please double check the assembly and 
installation instructions as well as the instructions for 
the proper control panel.  More troubleshooting tips 
can be found at www.kascomarine.com

“My Fountain trips the ground fault interrupter in the 
C-25, C-85, or C-95.”

 

This is the most common symptom of several 

possible problems.  To correctly diagnose the problem,  
you will need to collect more information.  A Ground 
Fault Interrupter (GFI) breaker that trips can in- 
dicate an electrical service problem, water contamina-
tion in the unit and/or cord, bad breaker, control  
box problems, motor problems, etc.  Try to fi nd out the 
answers to these questions before you contact  
Kasco to narrow down the problem.  

How long does it take to trip the breaker?  

• 

Does it always take the same amount of time to 

• 

trip?
How many times has it tripped?

• 

Has there been any electrical problems in the area 

• 

recently?

“My Fountain seems to run slowly.”

 

This can also be a symptom of several possible 

problems.  There could be an electrical problem where 
the unit is not getting the proper voltage.  This could 
also indicate a problem with the motor of the unit, 
which needs to be looked at by an Authorized Repair 
Center.  Check that the unit is receiving the   proper 
voltage, and, if so, contact Kasco for further steps.

“My Fountain hums, but will not start.  When I spin 
the prop with a stick, it starts up.”

 

This indicated a problem with the Starting 

Capacitor.  Each Kasco Fountain is equipped with a 
Starting Capacitor to get the unit going when it is fi rst 
plugged in.  If it is operating, but not spinning and can 
be started by spinning the prop with a stick, the Start-
ing capacitor needs to be replaced by an Authorized  
Repair Center.

“My Fountain turns itself off and back on without the 
timer and without tripping the GFI breaker.”

 

Each Kasco Fountain has a Thermal Overload 

built in that will turn the unit off when it overheats.  
Once the unit has cooled down, it will start back up.  If 

dress for correspondence regarding the warranty 
claim.

Any expedited shipping method for the return of the 
unit is at the customer’s expense.  Kasco Marine will 
return units repaired under warranty at our expense via 
ground freight within the continental United States.

Other Repairs:
Most failed equipment can be repaired at substantially 
lower costs than replacement with new.  Please ship 
according to the instructions in the previous section.  
Again, it is best to call ahead for a Return Authori-
zation Number and/or Repair Form so we know the 
repair is coming.

Kasco Marine does estimates on repairs at the request 
of the customer.  The request for estimate should be 
included in the letter that accompanies the returned 
unit and must include a daytime phone number and/or 
e-mail address.  Estimate options are as follows:

We will contact the customer with a total after the unit 
has been evaluated, but before the work is performed.
We will repair the unit only if repair costs are under a 
stated dollar amount.  Example: “Please repair if total 
is under $150.00 before shipping charges.”

All estimates that are rejected for repair will be de-
stroyed unless otherwise directed by the customer.  If 
the customer would like the unit returned, the unit will 
be restored as closely as possible to the condition in 
which it was received and shipped at the customer’s 
expense for shipping and handling charges.

Billing:

All non-warranty repairs will be returned to the cus-
tomer prepaid with Visa or Mastercard or shipped 
C.O.D. with C.O.D. charges unless otherwise directed.  
Kasco Marine will call for credit card information 
upon completion of the estimate.

All other warranty and repair inquiries should be di-
rected to Kasco Marine, Inc. at 715-262-4488 or 
[email protected]

Содержание 3400HJF

























Отзывы: