Kärcher SE 6.100, Руководство пользователя

Страница: 21 / 28

–
2
1
 Once the wastewater container is full, the appli-
ance switches off automatically.
Note : Once the appliance shuts off, switch off the
appliance, because the suction turbine will other-
wise start running again once you open the appli-
ance.
 Release and remove the appliance head.
 Remove the wastewater container and empty it.
 Rinse the spray tubes in the appliance as follows:
Fill the fresh water container with approx. 1 litre of
clear water.
Hold the nozzle above the drain, and switch on the
spraying pump until the clear water has been con-
sumed.
– Always work from the light to the shade (from the
window to the door).
– Always work from the cleaned to the uncleaned
surface.
– Carpets with jute backing can shrink and colours
may fade if too much water is used.
– Brush high-fiber rugs in the direction of the weave
after cleaning (using a fiber brush or a scrubber).
– Impregnating the fabric using the detergent Care
Tex RM 762 after wet cleaning prevents a quick
resoiling of the textile surface.
– Do not step on cleaned surfaces until they have
dried and do not place furniture on them to avoid
pressure spots or rust stains.
With light to normal contamination (regular clean-
ing)
:
 Turn on suction and spraying.
 Spray and simultaneously suction off detergent so-
lution in one work cycle.
 Switch off the spray switch and suction off the re-
maining cleaning solution.
 After cleaning the carpets, reclean them using
clear, warm water and waterproof if needed.
Heavy soiling or stains (basic cleaning):
 Switch on the spray.
 Apply detergent solution and allow to react for 5
minutes (vacuuming is switched off).
 Clean the surface just like you would with light/nor-
mal soiling.
 After cleaning the carpets, reclean them using
clear, warm water and waterproof if needed.
ATTENTION
Container and accessories must be dry, otherwise dirt
may adhere.
 Remove the wastewater and fresh water contain-
ers.
Illustration
 Recommendation : Insert the filter bag for vacu-
uming.
Illustration
 Use the adapter for wet/dry vacuuming Attach the
adapter to the handle, turn the locking handle to se-
cure it.
 Select the desired accessories and attach to the
spray/suction pipes or directly to the attachment.
 Switch on the vacuum process.
Note : Do not switch on the spray.
Vacuuming of hard floors
Illustration
 Use your foot to press the reversing switch of the
floor nozzle. The brush strips at the bottom of the
floor nozzle are extended.
Vacuuming carpeted floors
Illustration
 Use your foot to press the reversing switch of the
floor nozzle. The brush strips at the bottom of the
floor nozzle are retracted.
 Use the surrounding air separator to adapt the suc-
tion force.
Note:
Close the surrounding air separator again after
use!
ATTENTION
Do not use a filter bag!
 Remove the fresh and waste water containers, vac-
uum the wet dirt/water directly into the container.
 Use washing nozzle to vacuum up wet dirt/water.
 Once the wastewater container is full, the appli-
ance switches off automatically.
Note : Once the appliance shuts off, switch it off us-
ing the vacuum button, because the suction turbine
will otherwise start running again once you open
the appliance.
If you use a crevice nozzle:
 Attach and secure the adapter for wet/dry vacuum-
ing. Install the crevice nozzle directly to the adapt-
er.
 Switch on the vacuum process.
Illustration
 During interruptions in operation, the suction pipe
can be simply clipped into the accessories storage
and removed again.
Empty the wastewater reservoir during operation
End wet cleaning process
Cleaning tips/mode of operation
Cleaning methods
Dry vacuum cleaning
Vacuuming up moist dirt/water
Interrupting operation