Kärcher RCW 5, Руководство пользователя

Страница: 23 / 292

English 23
Note
Check the charging state of the battery before every use
of the cleaning robot.
If the battery status LED lights up or flashes red, the
charging state is insufficient for safe operation and the
cleaning robot does not suction onto the glass surface.
Place the cleaning robot in the station to charge the bat-
tery.
If the battery status LED is green, the charging state is
sufficient for safe operation.
4. Carefully position the cleaning robot with the handle
vertically aligned on the pre-cleaned glass surface
and hold it until it is securely attached and an audio
signal is emitted.
Illustration R
Note
If possible, place the cleaning robot at medium height of
the glass surface and min. 20 cm set the distance to the
right frame.
5. Select the desired cleaning program, to do this:
a Press the On / Off button once to activate the full
cleaning program.
The cleaning robot cleans the entire glass sur-
face.
Illustration S
b Press the On / Off button twice to activate the
Partial Cleaning program.
The cleaning robot cleans the glass surface be-
low the point to which it was attached.
Illustration T
Note
The cleaning robot first makes oscillating and circular
movements with a dry microfibre cleaning cloth to mois-
ten the microfibre cleaning cloth evenly with detergent.
This procedure can take several minutes.
Removing the cleaning robot from the glass
surface
1. At the end of the program, the cleaning robot stops
at its original position and emits a light and sound
signal.
Illustration U
Note
Remove the cleaning robot from the glass surface once
the program has ended.
2. Hold the cleaning robot by the handle, press the re-
lease button and carefully remove the cleaning ro-
bot from the glass surface after 2 - 3 s.
3. Loosen the lock nut and unhook the snap hook from
the loop on the cleaning robot.
4. Place the cleaning robot in the station with the mi-
crofibre cleaning cloth attached.
The detergent container of the cleaning robot is
filled. When the process is complete, the device sta-
tus LED lights up and a tone sounds.
Note
Depending on the fill degree, the cleaning agent con-
tainer of the cleaning robot is first emptied and then
filled again in order to ensure an optimal filling.
Removing the safety system
1. Remove the retractor from the glass surface:
Illustration V
1. Release the grey lever.
2. Place your finger under the tab of the suction cup
and remove the retractor.
3. Tension the grey lever.
3. Loosen the safety strap.
4. Place the retractor in the storage compartment
accessory of the station.
2. Wipe off any residue of the suction cup and main
seal from the glass surface with a soft, clean cloth.
Checking the cleaning robot for dirt
1. Check the underside of the cleaning robot for adher-
ing dirt and remove it before placing the cleaning ro-
bot on another glass surface or placing it in the
station (see chapter
Cleaning the cleaning robot ).
Care and service
Clean station
ATTENTION
Risk of damage due to improper cleaning of the sta-
tion.
Cleaning the station under running water (e.g. in the
shower) can damage the station.
Do not clean the station under running water, but wipe it
with a damp cloth if necessary.
1. If necessary, clean the charging station with a damp
cloth.
Cleaning the cleaning robot
몇
CAUTION
Danger of injury due to rotating drive wheels and
cleaning brushes.
There is a risk of injury due to body parts being crushed
on the rotating drive wheels and cleaning brushes.
Keep body parts such as fingers and hair as well as
loose clothing such as ties and scarves away from the
rotating drive wheels and cleaning brushes.
1. Replace the microfibre cleaning cloth as soon as it
becomes heavily soiled or the cleaning performance
decreases. Wash soiled microfibre cleaning cloths
at max. 60 °C, and the main seal at max. 40 °C in
the washing machine.
Do not use fabric softeners, do not bleach, do not
machine dry, do not iron.
2. Clean the squeegee blades and the suction cups
with a damp cloth as soon as they are visibly dirty or
the cleaning performance decreases.
Illustration W
3. Clean all drive rollers and the roller brush with a
damp cloth as soon as they are visibly dirty or the
cleaning performance decreases. To do this, simul-
taneously press the On / Off button and the release
button to switch on the roller drives.
The drive wheels and the cleaning brush rotate.
Illustration X
4. Release the power button and the release button.
The drive wheels and the cleaning brush stop.
5. If necessary, clean the casing of the cleaning robot
with a damp cloth.
Renewing the cleaning brush
Note
A damaged or worn cleaning brush reduces the clean-
ing performance and should be replaced immediately.