-
6
m
Danger
Long hours of using the appliance can
cause circulation problems on account of
vibrations.
It is not possible to specify a generally valid
operation time, since this depends on sev-
eral factors:
–
Proneness to blood circulation deficien-
cies (frequently cold extremities, tin-
gling, numbness).
–
Low ambient temperature. Wear warm
clothes to protect the affected body
parts.
–
A firm grip impedes blood circulation.
–
Continuous operation is worse than an
operation interrupted by pauses.
In case of regular, long-term operation of
the device and in case of repeated occur-
rence of the symptoms (e.g. tingling, numb-
ness in certain body parts) please consult a
physician.
Î
Pull seat adjustment lever outwards.
Î
Slide seat, release lever and lock in
place.
Î
Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.
Î
You can use the accelerator to regulate
the engine speed.
1
Transport drive
2
Sweeping with sweep roller
3
Sweeping using roller brush and side
brushes
Note:
The machine is equipped with a seat
contact switch If the driver's seat is vacat-
ed, the machine is switched off.
Î
Open the gas drawing valve by turning
it in anti-clockwise direction.
Î
Sit on the driver's seat.
Î
Bring the direction selector switch into
the middle position.
Î
Lock parking brake.
Î
Engine speed adjustment - push for-
ward by 1/3.
Î
Insert the ignition key into the ignition
switch.
Î
Turn the ignition key to position "II".
Î
If the machine starts, release the igni-
tion key.
Note:
Never operate the starter motor for
longer than 10 seconds. Wait at least 10
seconds before operating the starter motor
again.
Î
Set programme selection switch to
"Transport drive".
.
Î
Move the gas lever all the way to the
front (high speed).
Note
: The speed of the side brush and
the brush roller depends on the motor
speed.
Î
Press brake pedal and keep it de-
pressed.
Î
Release parking brake.
Î
Set the travel direction switch to "for-
ward".
Î
Press accelerator pedal down slowly.
m
Danger
Risk of injury! While reversing, ensure that
there is nobody in the way, ask them to
move if somebody is around.
Caution
Risk of damage! Only use the direction
switch when the machine is standing still.
Î
Set the travel direction switch to "back-
wards".
Î
Press accelerator pedal down slowly.
–
The accelerator pedal can be used to
vary the driving speed infinitely.
–
Avoid pressing the pedal suddenly as
this may damage the hydraulic system.
–
In the event of power loss on inclined
surfaces, slightly reduce the pressure
on the accelerator pedal.
Î
Release the accelerator pedal, the ma-
chine brakes automatically and stops.
Note:
The braking effect can be supported
by pressing the brake pedal.
Driving over fixed obstacles which are 70
mm high or less:
Î
Drive forwards slowly and carefully.
Driving over fixed obstacles which are
more than 70 mm high:
Î
Only drive over these obstacles using a
suitable ramp.
Caution
Do not sweep up packing strips, wire or
similar objects as this may damage the
sweeping mechanism.
Note:
To achieve an optimum cleaning re-
sult, the driving speed should be adjusted
to take specific situations into account.
Note:
During operation, the waste contain-
er should be emptied at regular intervals.
Note:
During operation, the dust filter
should be shaken off and cleaned at regu-
lar intervals.
Î
Switch on the blower.
Î
Set the programme switch to sweep
with sweeping brush when cleaning
surfaces.
Î
Set the programme switch to sweep
with sweeping brush and side brush
when cleaning edges.
Î
Switch off the blower.
Î
Set the programme switch to sweep
with sweeping brush when cleaning
surfaces.
Î
Set the programme switch to sweep
with sweeping brush and side brush
when cleaning edges.
Operation
Adjusting driver's seat
Adjust engine speed
Programme selection
Starting the machine
Open the gas supply
Start the engine
Drive the machine
Drive forward
Reverse drive
Driving method
Brakes
Driving over obstacles
Sweeping mode
Sweeping dry floors
Sweeping damp or wet floors
(1
Содержание KM 130/300 R LPG
Страница 2: ......
