Kärcher KM 130/300 R D, Руководство пользователя

Страница: 9 / 17

-
7
–
Rinse thoroughly with lots of clear water
if acid gets into the eye or comes in con-
tact with the skin.
–
Then consult a doctor immediately.
–
Wash off the acid If it comes in contact
with the clothes.

Insert battery in battery mount.

Screw on mounts on battery base.

Connect pole terminal (red cable) to
positive pole (+).

Connect pole terminal to negative pole
(-).
Note: Check that the battery pole and pole
terminals are adequately protected with
pole grease.
Caution
Regularly check the fluid level in acid-filled
batteries.
–
The acid in a fully charged battery has a
specific weight of 1.28 kg/l at a temper-
ature of 20 °C.
–
The acid in a partially discharged bat-
tery has a specific weight between 1.00
and 1.28 kg/l.
–
The specific weight of the acid must be
uniform in all cells.

Unscrew all cell caps.

Take a sample from each cell using the
acid tester.

Put the acid sample back into the same
cell.

Where fluid level is too low, top up cells
to the mark provided with distilled wa-
ter.

Charge battery.

Screw in cell caps.

Danger
Risk of injury! Comply with safety regula-
tions on the handling of batteries. Observe
the directions provided by the manufacturer
of the charger.

Danger
Charge the battery only with an appropriate
charger.

Unscrew all cell caps.

Connect positive terminal cable from
the charger to the positive pole connec-
tion on the battery.

Connect negative terminal cable from
the charger to the negative pole con-
nection on the battery.

Plug in mains connector and switch on
charger.

Charge battery using lowest possible
level of charging current.
Note: When the battery is charged, first re-
move the charger from the mains and then
disconnect it from the battery.

Disconnect pole terminal to negative
pole (-).

Disconnect pole terminal to positive
pole (-).

Loosen the mounts on battery base.

Remove the battery from the battery
holder.

Dispose of the used battery according
to the local provisions.

Danger
Risk of burns!

Allow engine to cool down.

Wait for at least 5 minutes after switch-
ing off the engine before checking the
engine oil fill level.

Pull out oil dipstick.

Wipe off oil dipstick and insert.

Pull out oil dipstick.

Read the value of the oil level.

Insert the oil dip again.
–
The oil level must lie between “MIN“
and “MAX“ marking.
–
Add motor oil if the oil level is below the
"MIN" marking.
–
Do not fill oil above the "MAX" marking.

Loosen the screw cap of the oil filling
opening.

Fill in motor oil.
Oil grade: see Technical Data

Close oil filler opening.

Wait at least 5 minutes.

Check engine oil level.
Caution
Risk of burns due to hot oil!

Ready a catch bin for approx. 6 litre oil.

Allow engine to cool down.

Unscrew oil drain plug.

Loosen the screw cap of the oil filling
opening.

Drain off oil.

Unscrew the oil filter.

Clean the intake and sealing areas.

Coat the washer of the new oil filter with
oil before fitting it.

Fit in the new oil filter and tighten it by
hand.

Screw in the oil drain screw along with
the new washer.
Note: Tighten the oil drain screw using a
torque wrench to 25 Nm.

Fill in motor oil.
Oil grade: see Technical Data

Close oil filler opening.

Let the motor run for approx. 10 sec-
onds.

Check engine oil level.
Note
The waste container must not be raised.

Open engine cover.
1 Looking glass
2 Manometer
3 Screw cap, oil fill opening

Check hydraulic oil level in the looking
glass.
–
The oil level must lie between “MIN“
and “MAX“ marking.
–
Add hydraulic oil if the oil level is below
the "MIN" marking.

Loosen the closing cap of the oil filling
opening.
Installing and connecting the battery
Check fluid level in the battery and ad-
just if required
Charging battery
Remove the battery
Check engine oil level and top up, if re-
quired
Change the motor oil and the oil filter
Check hydraulic oil level and refill hy-
draulic oil
9 EN