– 7
Ready a catch bin for appr 1 Litre oil.
Loosen release screw.
Tighten release screw.
Fill oil slowly up to the MAX marking.
Note:
Air pockets must be able to leak out.
For oil type refer to technical specifications.
DANGER
Risk of injury by inadvertent start-up of appliance and
electric shock. Prior to all work on the appliance, switch
off the appliance and pull the power plug.
–
Leak in the high pressure system
Check high pressure system and connections for
tightness.
–
Water shortage
Check water supply, check connections.
–
Obstructed reed switch in the water shortage safe
guard.
Check water shortage safe guard.
Figure 10
Exchange the poles at the appliance plug.
–
No line voltage, see "Appliance is not running".
–
Contactor error
Set the appliance switch to "0/OFF“.
Turn on the appliance.
–
Error occurs repeatedly.
Inform Customer Service.
–
Engine overload/overheat
Set the appliance switch to "0/OFF“.
Allow device to cool down.
Turn on the appliance.
–
Error occurs repeatedly.
Inform Customer Service.
–
Fault in the voltage supply.
Check main connections and mains fuse.
–
Excessive power consumption.
Check main connections and mains fuse.
Inform Customer Service.
–
The exhaust temperature limiter has been trig-
gered.
Set the appliance switch to "0/OFF“.
Allow device to cool down.
Turn on the appliance.
–
Error occurs repeatedly.
Inform Customer Service.
–
The flame sensor turned the burner off.
Inform Customer Service.
–
System care detection defective
Inform Customer Service.
–
Temperature sensor defective
Inform Customer Service.
–
Service interval
Perform service work.
–
Fuel tank empty.
Refill fuel.
Note:
Burner can operate 5 more hours.
–
System care tank is empty, due to technical rea-
sons a remainder stays in the tank.
Refill system care.
Note:
Burner operation no longer possible.
–
System care container is empty.
Refill system care.
–
Detergent tank 1 is empty.
Refill detergent.
–
Detergent tank 2 is empty.
Refill detergent.
–
No power
Check power connection/conduit.
–
Air within the system
Vent pump:
Set dosing value for detergent to "0".
With open hand spray gun turn device on and off
multiple times with the device switch.
Open and close the pressure/quantity regulation at
the pump unit with the hand spray gun open.
Note:
By dismantling the high pressure hose from the
high pressure connection the venting process is accel-
erated.
If detergent tank is empty, refill.
Oil change
Dispose of old oil ecologically or turn in at a gathering
point.
Troubleshooting
Indicator lamp pump
2x blinking
3x blinking
4x blinking
Indicator lamp rotation direction is blinking
Indicator lamp "Ready for use" turns off
Engine indicator lamp
1x blinking
2x blinking
3x blinking
4x blinking
Indicator lamp burner failure
1x blinking
2x blinking (option)
3x blinking
4x blinking
Indicator lamp service
Fuel indicator lamp glows
Indicator lamp system care is illuminated
Indicator lamp system care is blinking
Indicator lamp detergent 1 is illuminated
(HDS 12/18 only)
Indicator lamp detergent 2 is illuminated
(HDS 12/18 only)
Appliance is not running
Device is not building up pressure
22
EN
Содержание HDS 9/18-4 M
