background image

HDS 505, 508, 509, 510  •   9.800-078.0 - N

OPERA

T

OR’S MANU

AL

    

PRESSURE W

ASHER

  

10

98000780-12

OPERATING INSTRUCTIONS

STEP 1:

 Turn water on.

STEP 3:

 Grip spray gun handle 

se cure ly and pull trigger. Then turn 
variable pressure control handle 
counterclockwise.

STEP 2:

 Connect the power cord 

into the proper electrical out let, then 
push in the GFCI reset button. (Re-
 fer to se ri al plate for information). 

STEP 4:

 Before installing noz-

zle, turn on water supply and run 
machine, allowing water to flush 
through the system until clear.

Turn switch to pump po si tion. When 
a steady stream of water fl ows from 
the spray gun and wand the ma-
 chine is ready for cold water clean-
ing by turning the variable pres sure 
control handle clockwise to raise 
the pressure.

For hot water washing, turn the 
switch to the burn er position. (The 
burner will light au to mat i cal ly when 
the trigger on the spray gun is 
pulled.)

Selection of high or low pressure is accompanied by turn ing the han dle. 

NOTE:

 High pressure nozzle must be in sert ed at end of wand to obtain 

high pressure. To apply soap read operator's manual.

Variable Pressure 

Control Handle

Trigger

Variable Pressure 

Wand (VP)

High 

Pressure 

Nozzle

Brass Soap 

Nozzle

98000780-8

98000780-9

98000780-10

98000780-11

Содержание HDS 3.5/30 Ea Cage









































Отзывы: