manualshive.com logo in svg

Kärcher HD 9/50-4 Cage, Руководство по обслуживанию

Поделиться
Скачать
Kärcher HD 9/50-4 Cage Скачать руководство пользователя страница 14

14 

English 

5.906-441.0 Rev. 01 (06/10)

Install the intermediate gear:

Î

Slide the toothed gear onto the shaft of the high pressure 
pump.

Î

Align the toothed wheel so that the shaft protrudes by 13±0,2 
mm from the toothed wheel.

Î

Coat the threaded pin with soluble screw protection and tighten 
it.

1

Oil filling nozzle

2

Spacer disc 7.0 mm

Î

Fasten the intermediate gear to the combustion motor with 4 
spacer discs (7.0 mm) and 4 screws.
The washers under the screw head are only required on the 
elongated borings.

몇

Warning

Risk of damage. Use only spacer discs that are 7.00 mm long. The 
spacer discs included in the package of the intermediate gear are 
6.0 mm long and must not be used.

Î

Fasten the intermediate gear to the high pressure pump using 
4 screws.

Î

Fasten the high pressure pump to the counter holder

1

Oil level indicator

Î

Fill oil (SAE 90) into the oil fill neck while the appliance is in a 
horizontal position until the oil level reaches the upper edge of 
the oil level indicator.

4.5.7

Intermediate gear

Содержание HD 9/50-4 Cage






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды