Kärcher CV 66/2 Скачать руководство пользователя страница 10

Страница: 10 / 18

English

Position of the drive belt - display with removed appliance hood.

Loosen the screw on the support plate

Slide the support plate down to tension the drive belt

Make sure you slide the support plate straight - do not tilt

Check the tension of the drive belt, adjust if necessary

Tighten all screws on the brush motor support plate.

Reinstall the drive belt cover

There is a suction channel cover on the brush head. This channel
can be removed to clean the suction channel.

Remove the appliance cover

Loosen all 8 screws on the suction channel cover

Remove the suction channel cover

Clean the suction channel

Clean the suction channel seal prior to installation

If the seal was damaged during removal, it must be replaced:
Remove the old seal, clean the adhesive surfaces, apply new
seal.

Reinstall the suction channel cover

Reinstall the appliance hood

5.9

Clean/replace the suction channel

Содержание CV 66/2



















Результаты поиска

Содержание CV 66/2

Отзывы:

Бренды по названию

Популярные бренды

Kärcher CV 66/2, Руководство по обслуживанию

Результаты поиска

Содержание CV 66/2

Отзывы:

Бренды по названию

Популярные бренды