background image

     

5

Press Info button - the set value blinks.

Set the desired value by turning the info 
button.

Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10 
seconds. 

ATTENTION

Risk of damage to the floor covering. Do 
not operate the appliance on the spot.

Turn the program selection switch to 
the desired cleaning program. 

Press the pedal for lowering the clean-
ing head downwards slightly and then 
move it to the left. This unlocks the ped-
al. Release the pedal slowly upwards.
The cleaning head is lowered.

Note:

The brush motor comes to a halt when the 
machine stops and when there is overload.

Arrest the lever in the desired position.
Upper position: higher contact pressure
Lower position: reduced contact pres-
sure

Pull the lever out and press it down; the 
vacuum bar is lowered.

Note:

– For cleaning tiled floors, adjust the 

straight suction bar in such a way that 
cleaning is not done at an angle of 90 
degrees to the joints.

– The inclined position and the inclination 

of the suction bar can be adjusted to 
achieve better suction results (see "Ad-
justing the suction bar").

If the wastewater reservoir is full,

 the 

floater will close the suction opening 
and the suction turbine will run at a 
higher speed. If this is the case, shut 
the vacuum off and drive to empty the 
wastewater reservoir.

Close the regulatory button for setting 
the water quantity. 

Release drive lever/safety switch.

Set the program selection switch to suc-
tion or vacuuming.

Lift the cleaning head. 

Briefly drive forward and suck of the re-
maining water. 

Raise the vacuum bar.
The suction turbine will continue to run 
for 10 more seconds to suck off residual 
water from the vacuum bar and the vac-
uum hose.

Remove the Intelligent Key.

Charge battery, if required. 

WARNING

Please observe the local provisions regard-
ing the wastewater treatment.

Take the water discharge hose from the 
support and lower above a suited col-
lection device.

Crush or bend the dosing equipment. 

Open the lid of the dosing equipment. 

Drain off the dirt water - regulate the 
water quantity by pressing or bending. 

Rinse the waste water tank with clean 
water or with the rinsing system for the 
waste water tank (option).

Loosen the lid for emptying the fresh 
water slowly - do not remove it fully.
For a quicker emptying process, re-
move the entire lid.

To rinse the fresh water reservoir, re-
move the cover completely and remove 
the fresh water filter.

Plug in the Intelligent Key.

Select the desired function by turning 
the Info button.

The different functions are described in the 
following.

In this menu item, the authorisations for the 
yellow Intelligent Keys are released.

Press the info button while "Key menu 
>>“ is displayed.

Remove the grey Intelligent Key and in-
sert the yellow Intelligent Key to be pro-
grammed.

Select the desired menu item to be 
modified by turning the Info button.

Press Info button.

Adjust the menu item by turning the Info 
button.

Confirm the setting by pressing the 
menu item.

Select the next menu item to be modi-
fied by turning the Info button.

To save the authorisations, retrieve the 
menu "Save settings" by turning the info 
button and pressing it.

To exit, retrieve the menu "Exit menu" by 
turning the info button and pressing it.

Parameters that are adjusted with the grey 
Intelligent Key, are kept until another set-
ting is selected.

Turn the program selection switch to 
the desired cleaning program. 

Turn the info button until "Cleaning App 
>>“ is displayed.

Press the info button - the first adjusta-
ble parameter is displayed.

Press Info button - the set value blinks.

Set the desired value by turning the info 
button.

Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10 
seconds. 

Select the next parameter by turning 
the Info button.

After all desired parameters have been 
modified, turn the info button until "Exit 
menu" is displayed.

Press the info button - you will exit the 
menu.

Press Info button - the set value blinks.

Set the desired language by turning the 
info button.

Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10 
seconds. 

Adjust the trailing time of the brushes.

Same adjustment as "Set language".

Turn the info button until the function 
"Battery menu" is displayed.

Press the info button - select the charg-
ing marker line according to the built-in 
batteries.

Note

: Setting the charging marker line 

should be discussed with Kärcher cus-
tomer service. This applies especially if 
the battery is not listed in the menu.

Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10 
seconds. 

Recreate the basic settings.

Cleaning

Lower the cleaning head

Adjusting the brush contact pressure

Lower the vacuum bar

Shutting Down the Appliance

Drain off dirt water

Drain off clean water

Grey Intelligent Key

Key menu >>

Cleaning App >>

Setting the language

Brush trailing

Setting the charging marker line

LOAD DEFAULT

18

EN

Содержание B 60

























Отзывы: