①
②
③
・
・
・
・
・
・
・
・
・
・
・
・
・
①
②
③
④
⑤
①
②
③
④
⑤
⑥
2. Installation
Please establish to the horizontal position.
Please refer to the figure of the right about the
around of inclination. And, please establish to
the horizontal position about the right and left.
Please fix it firmly as occasion demands.
Place where can not establish
Place where back is stuck to wall etc.
Place where height is more than 1000m
Outdoor, and place where is exposed to the storm
Place where acid and corrosiveness gas is floating
Places of there are many dust
Room where is tightly sealed and case inside
Place where has vibration
Upper part of generation thing
Place where ambient temp. is more than 0 - +40
ﾟ
C.
Neighborhood of combustible
Place where ambient humidity is more than 85%R.H.
Place where air pressure is low
Place where has floating objects that pass electricity (Carbon fiber etc.)
3. Piping
Please fix the piping to the outlet and inlet certainly.
Leakage of the hot-air is occurred without fail on the characteristic of the flexible
hose in the case of the piping by the flexible hose to the outlet and inlet of hot-air
generator. Electron devices inside the operation panel are damaged by the hot-air
of the high temp. that leaked flows backward to the hot-air generator inside. So,
please execute the glass tape for the air leakage prevention that was enclosed to the
outlet and inlet.
Please pipe as thickly, short, and gradual curve as possible.
Please insulate sufficiently without fail to piping.
Please do not hang the pulling load to the outlet flange in the condition that the hot-
air generator with the outlet flange was fixed.
Execution example of the glass tape for
the air leakage prevention
Please do not insert the piping is smaller than the bore of the outlet to the outlet. Outlet sensor is bent, and
the sensor contacts to the heater.
4. Power supply
Please ask the connection of the power supply and ground construction work to the electric repairing work
technician.
Please connect the power cord in accordance with R(Red), S(White), T(Black), and Ground(Green).
Power cord is not belonged TSK-121. So, please prepare separately.(Recommendation cord : Cab tire cable 100mm
2
)
Please use the commercial power supply (50/60Hz) that has the sine wave-like to the power supply of the
hot-air generator. Please do not use the power supply that has the distortion wave including a high tone
wave from the frequency transformation device absolutely.
Please establish the exclusive use circuit. Please decide the capacity of the sensitivity current in accordance
with the following table in the case that the electric leakage circuit breaker is attached.
Model
Rough standard of the sensitivity current of the electric leakage circuit
TSK-18, 23, 33
50mA
TSK-42, 52, 52HT, 56
50mA
TSK -62, 72, 82
100mA
TSK-92, 102, 122, 132
200mA
* About 10 times of the early period leakage current are general as the sensitivity current of the electric leakage circuit breaker.
Please supply the power supply that the rating frequency that has the sine wave wave-like without fail was secured when the generator is
used to the power supply of the hot-air generator. Temp. is not controlled normally and the operation may not produced if the power
supply that rating frequency is not secured is supplied.
Please execute the ground construction work to prevent electric shock accident prevention. (Less than 300V
: D-class ground Less than 600V : C-class ground)
Attention
The voltage depression is occurred by too long wiring. So, please pay attention.
Attention
Please block the power supply without fail at the time of wiring and inspection. Please block the factory power supply without
fail because electricity is flowing to the control circuit even if the breaker (NFB) of the hot-air generator is turned OFF. You
receive an electric shock when work is conducted in the condition that the power supply is turned ON.
Attention
Please secure sufficient capacity in the case that the socket was established for connection. Socket may cause contact
defectiveness, absence phase, generation, and malfunction by passing year change. So, please refrain from the use of the
socket.
Attention
Hot-air generator is the device that is used in industry environment mainly. Radio wave obstacle may occur if this is used in
residence environment. User of this product must take the appropriate means for obstacle reduction.
－２－
15°
10°
