manualshive.com logo in svg

Kanomax 3443, Руководство по эксплуатации

Поделиться
Скачать
Kanomax 3443 Скачать руководство пользователя страница 10

2. Getting Started 
 

 

4

2. Getting Started 

 

2.1 Setting batteries or AC adapter

 

This instrument can use batteries or AC adaptor for its power. Set batteries in the instrument or connect the AC 
adaptor. 

2.1.1 Setting batteries 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

4.

 

Put the cover back on by reversing the above procedure.

1.

 

Slightly push the latch of the battery compartment 
lid in the direction of an arrow.

 

2.

 

While pushing the latch, lift the lid in the direction 
of an arrow. 

 

・

 

Manganese batteries (AA) 

・

 

Alkaline batteries (AA) 

・

 

NiMH batteries (AA) 

Types of batteries that can be used 

3.

 

Insert batteries ensuring that the battery polarity is correct. This 
instrument requires six (6) AA sizes batteries. Types of batteries 
that can be used are: Manganese, Alkaline or NiMH batteries. 
The six (6) batteries must be of the same type. Do NOT mix 
different types of batteries. Mixing different types of batteries 
may cause battery leakage or damage to the instrument. 

* Batteries CANNOT be recharged by the AC adapter. 

Содержание 3443



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды