KanexPro 4K HDBaseT MX-HDBASE4X4-4K Скачать руководство пользователя страница 6

Страница: 6 / 44

4K HDBaseT™ 4x4 Matrix Switcher

MX-HDBASE4X4-4K
KanexPro.com

4.3.7 Bi-directional RS232 Control .................................................................. 24

4.4 TCP/IP Control ................................................................................................. 25

4.4.1 Control Modes ........................................................................................ 25

4.4.2 GUI for TCP/IP control ........................................................................... 27

4.4.3 GUI Update ............................................................................................ 30

4.5 Firmware Update via USB ................................................................................ 30

5. Specification .............................................................................................................. 32

6. Panel Drawing ........................................................................................................... 33

7. Troubleshooting & Maintenance ................................................................................ 34

8. After-sales Service .................................................................................................... 36

Содержание 4K HDBaseT MX-HDBASE4X4-4K












































Результаты поиска

Содержание 4K HDBaseT MX-HDBASE4X4-4K

Отзывы:

Похожие инструкции для 4K HDBaseT MX-HDBASE4X4-4K

Бренды по названию

Популярные бренды

KanexPro 4K HDBaseT MX-HDBASE4X4-4K, Руководство пользователя

Результаты поиска

Содержание 4K HDBaseT MX-HDBASE4X4-4K

Отзывы:

Похожие инструкции для 4K HDBaseT MX-HDBASE4X4-4K

Бренды по названию

Популярные бренды