background image

11

Ultra  

1.54

Comfortable indoor climate in high-end interiors

Installation and operating instructions

4. Transport and storage

•  Please note all applicable safety and accident prevention regulations.
• Caution! Risk of sharp edges! Wear gloves, safety shoes and suitable 

protective clothing during transportation!

•  Two people are needed to carry the unit. Caution! Do not carry Ultra unit 

heaters by their louvres! Use suitable means of transport to avoid any 
damage to your health!

•  Please note the information printed on the packaging about storage and 

installing the unit on the ceiling.

Interim storage

Store the units in dry, dust-free and weather-proof rooms without any 
temperature fluctuations.
•  Never stack the units on top of each other to prevent damage to them!
•  Use the original packaging for storage.
•  Store Ultra unit heaters in the position shown on the packaging.

5. Technical data

1)

   Figures in brackets refer when the factory setting is changed to the max. possible speed. This is not suitable for cooling with 

dehumidification!

Technical data • Limits of use for cooling

Series

73

84

85

96

97

Enclosure type

IP 54

IP 54

IP 54

IP 54

IP 54

Water content [l]

1.6 - 2.3

2.0 - 2.9

2.0 – 3.8

2.2 – 4.4

3.3

Weight kg

28 - 30

34 - 43

35 - 45

45 - 55

57

EC model, 230 V series

/

84__33

85__33

96__33

96__34

97__33

AC model, 400 V series

73__36

84__36

85__36

96__36

/

/

AC model, 230 V series

73__16

/

84__16

/

85__16

/

96__16

/

/

/

Nominal speed  
EC model, 230 V rpm

/

1040

980

990

680 (990) 

1)

960

AC model, 400 V rpm

890

680

930

800

820

560

880

680

/

/

/

AC model, 230 V rpm

880

/

940

/

800

/

910

/

/

/

/

Cooling options

EC model, 230 V type

/

843133

853133 
854133

963133 
964133

963134 
964134

973133

AC model, 400 V type

/

843136

853136 
854136

963136 
964136

/

/

AC model, 230 V type

/

843116

/

853116 
854116

/

963116 
964116

/

/

/

Dry cooling

/

yes

yes

yes

yes

yes

yes

yes

yes

yes

Cooling with dehumidification

/

yes

yes

yes

yes

no

yes

yes

yes

yes

Содержание Ultra Series













































Отзывы: