Kamco CLEARFLOW CF90: QUANTUM Скачать руководство пользователя страница 13

 

 

INHIBITION AND CORROSION PROTECTION 

 

 

 

IMPORTANT 

 
1. The system is now full of fresh, clean water, and in 

line with Building Regulations Part L : 2006, a 
good quality corrosion inhibitor, such as 
SYSTEMSAFE DM, must be added to the system 
water to prevent further corrosion and scaling. 

 

To comply with Benchmark documentation, 
inhibitors must have passed the DWTA  
(Domestic Water Treatment Association) product 
performance standard and can be identified by 
this logo on the pack. 
 

 

 

The inhibitor may be added to the system by 

using the Quantum pump as follows: 

 
2. Briefly open a dump valve to lower the water level 

in the tank to just above the minimum level, close 
the dump valve. Add the SYSTEMSAFE DM 
inhibitor into the tank. Allow circulation through 
the system for ten minutes, isolate the flushing 
pump from the heating system, and switch off. 

 
3. If the system is vented, the residual water in the 

Quantum tank, which will contain a small quantity 
of inhibitor, may be poured into a bucket and 
added to the F&E tank after this has been 
cleaned. 

 

Note: In a pressurised system the inhibitor may 
be injected into the system using an IK6 injector, 
which will avoid wasting any inhibitor left in the 
Quantum tank.   (see page F.5). 

 

 

UPON COMPLETION 

 
1. Restore system to normal, restoring radiator 

balance valves to original settings, removing any 
temporary isolating valves or caps on the 
expansion and cold feed pipes, and restoring non 
return valves to normal operation if necessary. 

 
2. Before re-connecting the feed & expansion tank, it 

should be thoroughly cleaned, removing all traces 
of dirty water and sludge, and then disinfected 
with Kamchlor chlorine release tablets. 

 
 

The Quantum is also a very powerful descaling 

pump, suitable for use when descaling 

combination boiler domestic water heat 

exchangers, any conventional domestic boiler, 

water heaters, direct fired water heaters, thermal 

store type water heaters, showers, and 

calorifiers. 

 

Issue: Mar 2008 

Section B  – Using the Quantum for Power Flushing

 Page 

B.10 

© Kamco

Содержание CLEARFLOW CF90: QUANTUM














Отзывы: