11
10
2. Once the room temperature feels
comfortable, turn the variable
thermostat control slowly to the
minimal position until a click
sound is heard. This thermostat
control is now activated and
will automatically cycle the fan
heater off and on to maintain
the desired temperature.
Setting the Oscillation
(KFH770 only)
The oscillation function will work in
all heat and fan modes. Switch the
‘SWING’ button to ‘I’ to activate. This
will allow the heater to oscillate back
and forth. To stop the unit oscillating,
switch the ‘SWING’ button to ‘0’.
Safety Features
Safety Tip-Over Cut-Out Switch
There is a tip-over switch fitted to
the base of the heater. If the heater
is accidentally tipped over, the
heater will stop operating. Once
placed back into the upright position,
the heater will switch on again.
ThermoGuard Overheating
Safety Device
Your heater is fitted with a safety
device that switches off the heater in
the event of overheating.
Should this heater stop working,
turn off the heater and inspect the
air inlet and outlet for blockages.
Wait until the unit is fully cooled for
the protection system to reset before
attempting to restart the heater.
If the heater fails to operate or the
safety device switches off again,
take the heater to your nearest
Kambrook service centre for
examination or repair.
WARNING:
To avoid over
heating, do not cover the
fan heater.
WARNING:
KFH700 heater
is not equipped with a
device to control the
room temperature. Do
not use KFH700 heater
in small rooms when
they are occupied by
persons not capable
of leaving the room on
their own unless constant
supervision is provided.
Hints & Tips to Retain Heat in
Your Home
• Don’t overheat your home. The
temperature of a heated room in
winter should be 18-21°C.
• Your heater will work more
efficiently if you stick to Kambrook’s
recommended clearance spaces.
• Choose the right size heater for the
room type you want to heat.
• Zone off unoccupied rooms by
closing doors and only heat the
main living areas. Fit window
coverings like curtains to halve
winter heat loss.
• Put draft stoppers, such as a rolled
up towel, at the bottom of outside
doorways to keep out cold air.
• Keep the heat in and the cold
out by installing wall and ceiling
insulation.
• Avoid placing items too close to
the heater (both at the front and
back) for optimal air flow.
Using Your Kambrook Heater
Before First Use
Remove your heater from its carton
and associated protective wrapping.
Unwind the cord to its full length and
remove any protective cardboard
or foam that may have been used
to minimise transportation damage.
Place the heater on a firm, level
surface in a stable upright position.
Visually inspect the air inlet and
outlets to ensure no foreign material is
blocking these areas.
Turning Your Heater On
Before turning the heater ON, turn
the variable thermostat control (for
KFH710 & KFH770 models only) to the
minimum position, then turn the heat
settings control to the ‘OFF’ position.
Plug the cord into a 230V or 240V
electrical outlet and switch on. Be
sure the plug fits tightly as a loose fit
may cause overheating and damage
the plug.
WARNING:
To avoid an
electrical circuit overload,
it is recommended that
no other appliances are
plugged into the same
circuit with your heater
when you switch the
unit on.
Turn the variable thermostat control to
the maximum position, and then turn
the heat setting control to the desired
heat setting.
The fan heater has four modes;
OFF - Shuts off the heater and fan
FAN - For fan only operation
1 - Low heat setting (1200 watts)
2 - High heat setting (2400 watts)
Turning the heat settings control to
setting ‘1’ will set the heater into low
heat mode (1200 watts).
Turning the heat settings control to
setting ‘2’ will set the heater to high
heat mode (2400 watts).
Turning the heat settings control to fan
mode
is for fan-only operation with
no output of heat.
To turn the heater OFF, turn the heat
setting control to the ‘OFF’ position,
and turn the variable thermostat
control (for KFH710 & KFH770 models
only) to 'MIN' position. Turn off at the
power outlet and remove the plug
from the power outlet.
WARNING:
Do not use
this fan heater with an
external programmer,
timer or any other devices
that switches the fan
heater ON automatically
since a fire risk may exist
if the heater is covered or
positioned incorrectly.
Setting the Variable
Thermostat Control
(For KFH710 & KFH770
models only)
The variable thermostat control can
be used to maintain your desired
room temperature.
1. To set the desired temperature,
turn the heat setting control to
setting ‘2’ and turn the variable
thermostat control to the ‘MAX’
position to set the heater into
high heat mode.
