KAM Simple Precision OFD Скачать руководство пользователя страница 7

Страница: 7 / 23

OFDMANUAL 0816

I N S TA L L AT I O N

LOCATION

For optimal batch detection, KAM CONTROLS recommends that you install the in-station OFD™ sensor at the

first accessible pipeline location inside the terminal fence-line — upstream of the interface cut valve(s). This al-

lows the operator ample time to open/close the cut valves prior to the arrival of the product interface.

KAM CONTROLS also strongly recommends that you utilize a preview (or out-station) OFD™ sensor. This lets the

operator decide how to optimize each batch cut prior to actually making the batch cut at the in-station and gives

the operator more confidence in their decisions as well as the time to identify and resolve any issues that may

arise during a critical interface.

OUT-STATION/PREVIEW

OFD

INCOMING

OFD

TYPICALLY
1 - 2 MILES

(1.6–3.2km)

TO TANK

IN-STATION/CUT

OFD

TERMINAL FENCE LINE

CUT VALVES

TERMINAL FENCE

FIG. 3-1

RECOMMENDED OFD™ LOCATIONS

PRIOR TO INSTALLATION

Remove all the protective packaging materials including the red cap placed at the tip of the sensor probe. En-

sure that the OFD™ sensor was not damaged during transit.

CAUTION: Do not stand the OFD™ sensor on the probe end or allow the probe to hit the ground or any hard

surface under any circumstances. This will damage the lens, and the OFD™ sensor will not work properly.

Содержание Simple Precision OFD
























Результаты поиска

Содержание Simple Precision OFD

Отзывы:

Похожие инструкции для Simple Precision OFD

Бренды по названию

Популярные бренды

KAM Simple Precision OFD, Руководство пользователя

Результаты поиска

Содержание Simple Precision OFD

Отзывы:

Похожие инструкции для Simple Precision OFD

Бренды по названию

Популярные бренды