Kalamazoo K1000HB-2-NA, Инструкция по использованию и уходу

Страница: 23 / 64

+1.800.868.1699 41 KalamazooGourmet.com 40
Before You Cook
A quick safety check should be performed before each time you use the grill.
1. Clean and inspect the gas hose. If there is evidence of abrasion, wear, cuts or leaks, do not use the
grill. The hose must be replaced prior to using the grill. Replace the hose assembly with the exact type
specified by Kalamazoo Outdoor Gourmet.
2. Ensure the gas hose is clear of the grill. Keep the fuel supply hose away from all surfaces of the grill.
3.
Check that the area near the grill is clear of combustible materials and vapors, including alcohol,
gasoline, aerosol containers and dry goods. Keep electrical cords from being in contact with any
surfaces of the grill.
4.
Do not use the grill with overly loose-fitting clothing, especially loose sleeves that may come in contact
with the hot surfaces inside or outside the grill.
5.
Have insulated gloves with long cuffs ready and available.
While You are Cooking
1. Never move the grill while it is in use or when it is hot.
2.
The use of alcohol, prescription or non-prescription drugs may impair your ability to properly assemble
or safely operate the grill.
3. Do not touch the grill lid, any surfaces inside or around the cooking surfaces, the surface of the Hybrid
Fire Grilling Drawer or any surfaces inside the cabinet below the grill while the grill is hot. These
surfaces can cause serious burns.
4.
Be very careful transporting hot food. Sauces, juices and oils can cause serious burns to yourself or
those around you.
5. Only use a brass or stainless steel bristle brush, or wooden grate scraper, to clean the cooking surfaces
and warming rack. Wear insulated gloves with long cuffs to protect your hands.
6. Never empty the ash pan while the grill or the contents of the pan are hot. Always wait at least 24
hours after the grill has been hot before emptying the ash pan.
Follow all warnings and instructions when using this appliance.
This appliance is not intended for and should never be used as a heater.
This appliance is not intended for commercial use.
Ignition Burner
View Port
Lighting Your Grill
Before lighting your grill, be sure you have followed the instructions in this Use and Care
Guide regarding proper setup, placement, gas connections leak testing (see page 15) and
safe operation, all of which precede this page.
IMPORTANT: Do not use the grill if the odor of gas is present at any time. Follow leak
testing procedures before using the grill.
Standard Lighting Procedure:
1.
Open the grill lid.
2.
Make sure all control knobs are in the OFF position.
3. Turn the main gas supply on.
4. To light one burner at a time, press the control knob
inward. The bezel light should flash white. Continue
pressing in for 4 seconds, which is 4 flashes of the bezel
light. This pre-heats the hot-surface igniter.
5. While continuing to press inward, rotate the knob 90
degrees counter-clockwise to the HIGH/START position
(see Figure 16). This begins the flow of gas.
6. Keep pressing inward. Listen and watch for the burner to ignite.
If the burner does not ignite within five seconds return the valve
back to the OFF position.
Wait five minutes for the gas to clear before trying
again to light the burner.
7. Once the burner has lit, you must continue pressing in on the valve while the safety thermocouple heats
up. This can take up to 20 seconds. Once the bezel light changes from flashing white to flashing blue,
release the control knob. The bezel light should change to a steady orange glow.
IMPORTANT:
This grill uses safety valves to help protect you and your property. These
valves are connected to thermocouples designed to sense when there is flame coming from
the burner. Once the burner is lit, it takes up to 20 seconds for the thermocouple to heat up.
During this time, the safety device must be bypassed by pressing inward on the control knob.
It is very important to observe the burner has successfully lit during this time. If it has not
successfully lit, gas will be flowing into the grill, which can result in serious injury.
If you stop pressing in before the thermocouple has heated up, the safety device will cut off
the flow of gas to the burner and the flame will go out. You will have to reignite the burner.
After returning the control knob to the OFF position, follow steps 4 through 7 above.
Barbecue Burner
View Port