KAESER M100 Скачать руководство пользователя страница 183

Страница: 183 / 384

The tensioning device uses spring force to apply correct tension to the belts over a certain range.

The tensioning dimension

is controlled by adjusting the belt (see fig. 92).

Tensioning dimension:
■ Adjusting distance: 0.39 in
■ Minimum distance: 0.2 in

1. Check the tensioning distance

on the belt adjustment

Re-tension the belts if the tensioning dimension is below the minimum.

2. Reconnect the negative battery terminal.
3. Close the door.

10.8.8.3 Changing/tensioning the drive belt

Fig. 92 Generator belt tensioning

Support for belt tensioner

Hexagon nut

Spherical seat washer

Conical seat washer

Hexagon nut (locknut)

Drive belt

Generator drive pulley

Generator swing frame

Belt adjustment

Compression spring

Hexagon nut (self-locking)

Generator

Tensioning dimension

Tensioning the drive belt:

1. Loosen the locking nut

2. Turn the tensioning nut

to tighten the belt

until the tensioning dimension

corresponding

to the set distance is reached.

3. Tighten the locknuts

and

4. Replace the belt guard.
5. Reconnect the negative battery terminal.
6. Close the doors.

10 Maintenance

10.8 Maintenance for Optional Items

No.: 9_6999 23 USE

Operator Manual Screw Compressor
M100

171

Содержание M100

































































































































































































































































































































































































Результаты поиска

Содержание M100

Отзывы:

Похожие инструкции для M100

Бренды по названию

Популярные бренды

KAESER M100, Руководство оператора

Результаты поиска

Содержание M100

Отзывы:

Похожие инструкции для M100

Бренды по названию

Популярные бренды