background image

DANGER

Compressed air!
➤ Compressed air and pressurised components can injure or cause death if the contained

energy is released suddenly.

Fig. 14 Venting the machine

1

Relief and load valve

2

Venting and condensate valve

1. Shut down the machine using the «OFF» key.
2. Isolate the machine from the air consumers.
3. Switch off the power supply isolating device (disconnect the plug/plug connection) (all poles).

Machine is venting completely (relief and load valve/venting and condensate valve).

4. Check for zero pressure.

10.6  Venting the crankcase (de-pressurising)

After being switched off, the machine is still under pressure from the air consumer up to the non-

return valve.

De-pressurise the crankcase before carrying out any service functions.

The crankcase is de-pressurised by means of the safety valve.

Precondition The machine has cooled down.

DANGER

Compressed air!
➤ Compressed air and pressurised components can injure or cause death if the contained

energy is released suddenly.

10 Maintenance

10.6 Venting the crankcase (de-pressurising)

44

Operator manual    Reciprocating compressor  
i.Comp 3  

No.: 901731  24E

Содержание i.Comp 3

















































































Отзывы: