Kaba Saflok MT RFID Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 8

Kaba Saflok MT RFID Скачать руководство пользователя страница 7

© SAFLOK, all rights reserved.

INS_MTRFID_2_12

MT

TM

RFID Installation Instructions

Pg 7 of 8

Testing Lock Functionality

Pass a Construction key over the Quantum RFID reader. The green light will flash for five seconds.
Be sure that the green light flashes for five seconds while the exterior lever remains operable. If the
green light does not flash, refer to the table below.

Lock Communication

Electronic Function Description

Red and green LEDs flash

Time and date not set, use the Hand held and Quantum RFID

nine times simultaneously

LPI probe to reset

or for 5 seconds

Yellow LED flashes 12 times

Dead bolt is thrown or switch cam is not properly aligned

Yellow LED flashes two times

Keycard not allowed OR keycard cancelled by new keycard

Red and green LEDs flash

Low battery (contact the SAFLOK service department)

alternately nine times

Yellow and red LEDs flash

Bad keycard read or corrupted data (may require new

two times simultaneously

keycard) – Error logging to keycard. Hold keycard in front of the

lock reader longer.

Red and yellow LED flashes two times

Keycard not read (Key reader may be damaged)

«
...
5
6
7
8
»

Содержание Saflok MT RFID









Отзывы:

Нет отзывов