Kaba Saflok MT RFID Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 8

Kaba Saflok MT RFID Скачать руководство пользователя страница 1

MT

™

RFID Installation Instructions

All parts needed to install the MT™ RFID lock are included with each unit. Please check to make
sure all parts are accounted for before beginning installation. Do not substitute any of the parts.
The use of substitute parts will result in poor performance of the lock.

All information contained herein, including but not limited to product pricing and other intellectual property, is confidential and
intended for the sole use of the addressee(s) so named. Any misuse of this confidential information contained herein may result in
legal action by Computerized Security Systems dba SAFLOK and its parent company.

Optional

Communication

Modules

I/S Chassis Assembly

I/S Escutcheon

30320-H-Color — Assy, Strike, Buttons

A29030-Color — Screw Pack,

MT Universal 1-3/4 — 2-1/4

Mortise (see Mortise Options table)

51190-Color — Outside Front

A23390

(optional gasket for exterior use)

A21290-X-X-Color — O/S Housing Assy, MT RFID w/USB

A70000-Handing
Mortise, 1-3/4

A70020-Handing
Mortsie, 1-3/4
ADB

A70080-Handing
Mortise, 1-3/4
ADB, DAJ2

A70060-Handing
Mortise, 1-3/4
STD, DAJ2

Mortise Options

1
2
3
...
»

Содержание Saflok MT RFID









Отзывы:

Нет отзывов