K-TRON KSU-II/KCM Скачать руководство пользователя | Manualshive

Страница: 39 / 121

background image

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 39

Programming Reference

1

Machine setup menu 1.7

1.7.6

Motor sub-menu for AC Interface drive

Parameter

Definition

GEAR REDUC

Gear Reduction or Total

Gear Reduction

This parameter is used if the Screw Modulation or the Auto Gear
Reduction functions are used. This entry must be the total reduction
value between the drive motor and the feed screw. This entry is the
lowest reduction or simply provides the highest screw speed for any
given motor rpm.

Input range: 0 to 999

Default: 0

GEAR REDUC L

Gear Reduction Low

This parameter is used if the Auto Gear Reduction function is used.
This entry must be the total reduction value between the drive motor
and the feed screw. This entry is the highest reduction or simply
provides the lowest screw speed for any given motor rpm. This entry
is checked against the GEAR REDUC value to be sure that the
magnitude of the entry is correct.

Input range: 0 to 999

Default: 0

PICK UP TEETH

Speed Pickup Teeth

Input of the number of teeth on the pick up gear.

This gear is used for measuring the speed.

Input range: 0 to 9999

Default: 120

MAX MOT SPEED - [rpm]

Maximum Motor Speed

Input of the maximum motor rpm for 100% drive command.

Input range: Drive specific.

Default: drive specific

(See nameplate on motor for value)

MDU STATUS

MDU Status

The MDU status codes reveal operational condition of the Drive. See
listing of MDU status codes in section

DC CEILING-[%]

Drive Command Ceiling

Limitation of the drive command output to the motordrive.

Input range: 10 to 125%

Default: 110%

«
...
37
38
39
40
41
...
»

Содержание KSU-II/KCM


























































































































Отзывы:

Нет отзывов

Похожие инструкции для KSU-II/KCM

Бренд: Haier Страницы: 58

Minas A4 Series

Бренд: Panasonic Страницы: 5

Бренд: Jafar Страницы: 9

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 32

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Fantech Страницы: 2

Бренд: Sanhua Страницы: 3

Бренд: National Instruments Страницы: 78

Бренд: ECKELMANN Страницы: 147

Markoprint iJET

Бренд: Weber Страницы: 127

Easyflow J7 DN15

Бренд: Neles Страницы: 12

CIMR-VC*****H**-00 series

Бренд: YASKAWA Страницы: 32

Бренд: Samson Страницы: 182

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды