K-TRON KSU-II/KCM Скачать руководство пользователя | Manualshive

Страница: 23 / 121

background image

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 23

Programming Reference

1

Alarm menu 1.3

1.3.2

Alarm setup sub-menu

Parameter

Definition

ALARM DELAY [sec]

Alarm Delay

Time between the alarm detection and activation of the alarm relay
output when the alarm is of the type <Timed> or <Timed-Stop>. The
alarm output will not be activated and the alarm will be cancelled if
the fault is corrected within this time period.

Input range: 0 to 999 seconds Default: 30 seconds.

STARTUP DELAY [sec]

Startup Delay

Time during which process related alarm signals are suppressed
when the machine is being started up. See section

.

e.g. Massflow High error is suppressed.

Input range: 0 to 999 seconds Default: 60 seconds.

STOP CLRS ALARM

Clear Alarm on Stops

Select <Yes> if alarms are to be cleared when a stop occurs. Select
<No> if alarms are not to be cleared during a Stop action.

Default: No

ALR

Number of Selected

Alarm

Input of the alarm number, which can be selected from the list in the
appendix. With the programming variable ALARM MODE the
selected alarm number can be influenced.
Input range: See section

ALR

Name of Selected Alarm

Shows the alarm function for the selected alarm number.

ALARM MODE

Selected Alarm Mode

The selected alarm at the variable Alarm number can be influenced
as follows:

Setting

Definition

IGNORE

Alarm will be ignored.

IMMED

Alarm will be activated immediately but ALS output
will not change.

IMMED-STOP

Alarm will be activated immediately and ALS
output switches ON.

TIMED

Alarm will be activated after entered startup up-
and alarm delays but ALS output will not change.

TIMED-STOP

Alarm will be activated after entered startup and
alarm delays and ALS output switches ON.

Selection will depend upon the action desired.

Table page 1 of 2

«
...
21
22
23
24
25
...
»

Содержание KSU-II/KCM


























































































































Отзывы:

Нет отзывов

Похожие инструкции для KSU-II/KCM

Бренд: K&K Страницы: 6

Бренд: KELCO Страницы: 36

Бренд: Yardney Страницы: 8

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 98

CompactRIO cRIO-9002

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 145

Бренд: National Instruments Страницы: 42

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 54

Бренд: Ziton Страницы: 28

Бренд: Unico Страницы: 164

Бренд: DANIEL Страницы: 48

Бренд: Auber Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды