K-TRON KSU-II/KCM страница 21 Скачать руководство пользователя

Страница: 21 / 121

Docu-No.: 0590020601-EN Rev. 1.6.0

Page 21

Programming Reference

Alarm menu 1.3

1.3

Alarm menu

This menu sets the alarm parameters and limits.

1.3.1

Limits sub-menu

Any alarm that is set in percent, is disabled when the entry is <0>.

Parameter

Definition

MASSFLOW ERR+[%]

Massflow (+) Alarm Limit

MASSFLOW-[%]

Massflow (-) Alarm Limit

Massflow error limit is the permissible difference in percentage
between the setpoint and mass flow without triggering an alarm.

Input range: 0 to 100%

Default:10%

DRIVE CMD HI [%]

Drive Command High

Limit

The Drive Command High alarm is triggered when <Actual Drive
Command> exceeds this value.

Input range: >DRIVE CMD LO to 102%

Default: 99%

DRIVE CMD LO [%]

Drive Command Low

Limit

The Drive Command Low alarm is triggered when <Actual Drive
Command> is below this value.

Input range: < DRIVE CMD HI to 0%

Default: 0%

FF DEV LIM [%]

Feedfactor Deviation

Limit

Maximum permissible difference between the AVG FF (Average
Feedfactor) and the INIT FF (Initial Feedfactor). Not for vibratory
feeders.

Input range: 0 to 100%

Default:0%

MAX REF TIME [sec]

Refill Time Max or Refill

Time Maximum

Input of the maximum refilling time. See section

3.1.4

for more detail.

If the maximum/upper refilling limit is not reached when this time has
passed, an alarm will be triggered.

Input range: 5 to 999 seconds Default: 30 seconds

NW LO LIMIT

Net Weight Low Limit

Minimum product level, by weight, below which an alarm is
immediately triggered. If this condition is triggered, the controller
switches to volumetric control.

This value is only active if Refill is Enabled.

Input range: 0 to < REFILL MIN Default: 0.0 kg-no alarm

Table page 1 of 2

Содержание KSU-II/KCM


























































































































Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды

K-TRON KSU-II/KCM, Инструкция по программированию

Результаты поиска

Содержание KSU-II/KCM

Отзывы:

Похожие инструкции для KSU-II/KCM

Бренды по названию

Популярные бренды