K-Rain 2000 Series Скачать руководство пользователя страница 11

Страница: 11 / 12

III. PROBLEM

Controller does not turn ON in manual mode.

CAUSE:

No power to controller.

SOLUTION: Be sure that controller is properly wired as per Electrical Circuit and

Connection Diagram.

SOLUTION: Check circuit breaker.

IV. PROBLEM

Controller fails to operate properly in automatic (AUTO) mode.

CAUSE:

Day Wheel not properly programmed.

SOLUTION: Check Setting and Operation Instructions for programming day wheel.
CAUSE:

Auto-Off-On knob not set properly.

SOLUTION: Turn Auto-Off-On knob to auto position.
CAUSE:

Switch adjustment needed.

SOLUTION: Remove controller face from enclosure after disconnecting power to unit.

The switch adjustment screw is located on the switch cover. A clicking of

the switch should be heard when the switch arm is slowly pulled back at

the halfway point between the edge of the time dial and the far edge of the

timing pin. With a small screwdriver, tighten the screw clockwise to cause

the switch to activate sooner. If switch is activating sooner than desired,

turn adjustment screw counter-clockwise slightly.

CAUSE:

Switch contacts or relay worn out.

SOLUTION: Replace switch or relay (see parts list), ensuring that the controller is

properly rewired. NOTE: A nut driver tool is available to assist in removing

black retainer nuts.

Should the above troubleshooting tips fail to correct the problem you may be having,

please consult your local K-Rain

distributor for service or replacement.

Содержание 2000 Series













Результаты поиска

Содержание 2000 Series

Отзывы:

Бренды по названию

Популярные бренды

K-Rain 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание 2000 Series

Отзывы:

Бренды по названию

Популярные бренды