K-array KA7 Скачать руководство пользователя страница 25

ENGLISH

25

KA7

KA7-7

Output power

Max power 

2 x 350 w

(EIAJ)

4 x 350 w

(EIAJ)

Max power 

2 x 190 w 

(EIAJ)

4 x 190 w 

(EIAJ)

Max power - bridged 

1000 w

(EIAJ)

Max power - bridged 

700 w

(EIAJ)

Connectors

2 x 4-pin Speakon 

2 x 4-pin Speakon

Speakon 1 wiring

pin 1+,1- = CH1 pin 2+, 2- = CH2

pin 1+,1- = CH1 pin 2+, 2- = CH3

Speakon 2 wiring

pin 1+,1- = CH2  pin 2+, 2- = N.C.

pin 1+,1- = CH2  pin 2+, 2- = CH4

Audio specs

Slew rate 

30V/

m

S

30V/

m

S

S/N Ratio

>113 dB/A

>113 dB/A

Distorsion (THD, DIM, SMPTE)

<0.005%

<0.005%

Input impedance

20K bal. 10K unbal.

20K bal. 10K unbal.

Gain

32 dB

32 dB

Output

Unbalanced to ground

Unbalanced to ground

Bandwidth

3 Hz - 45 KHz

3 Hz - 45 KHz

Damping factor 8Ω (100 Hz) 

>1000

>1000

Protection

Thermal protection

Yes

Yes

Short circuit / over-load

Yes

Yes

Clip limit, 

Analog signal limit

Yes

Yes

Audio Input

Connectors

2 x Male + 2 x Female 3-pin bal .XLR

2 x Male + 2 x Female 3-pin bal .XLR

Wiring

Pin1 = Ground / Pin2 = hot (+) / Pin3 = cold (-) Pin1 = Ground / Pin2 = hot (+) / Pin3 = cold (-)

Remote control Input

Connectors

RJ45 / USB

RJ45 / USB

Remote control

Protocol

RS485 / USB

RS485 / USB

Power Input

Connectors

2 x PowerCon IN/OUT

2 x PowerCon IN/OUT

AC power

Operating range

90 - 260 Vac 50-60Hz with PFC (auto range) 90 - 260 Vac 50-60Hz with PFC (auto range)

P. nom

140 VA

140 VA

Max input voltage

265 Vac

265 Vac

Power factory

(1/2 max out/ 

8Ω)

0.97

0.97

Minimum operation voltage

70 Vac

70 Vac

Physical

Dimensions

20 (1/2 U rack) x 8.8 (2U rack) x 27 cm 

(7.87”x 3.46”x 10.63”)

20 (1/2 U rack) x 8.8 (2U rack) x 27 cm 

(7.87”x 3.46”x 10.63”)

Weight

4.03 Kg (8.89 lbs)

4.44 Kg (9.79 lbs)

Notes for data 

New materials and design are introduced into existing products without previous notice. Present systems may differ in some 
respects from those presented in this brochure

14. TECHNICAL DETAILS

Содержание KA7





























Отзывы: