background image

27

Appendix A  Calibration

This  chapter  introduces  the  calibration  process  to  minimize  analog  input  measurement 

errors.

A�1    Calibration Constant

The PCIe-69814 is factory calibrated before shipment, with associated calibration constants 

written  to  the  onboard  EEPROM.  At  system  boot,  the  PCIe-69814  driver  loads  these 

calibration constants, such that analog input path errors are minimized. JYTEK provides a 

software API for calibrating the PCIe-69814.
The  onboard  EEPROM  provides  two  banks  for  calibration  constant  storage.  Bank  0,  the 

default  bank,  records  the  factory  calibrated  constants,  providing  written  protection 

preventing erroneous auto-calibration. Bank 1 is user-defined space, provided for storage 

of self-calibration constants. Upon execution of auto-calibration, the calibration constants 

are recorded to Bank 1.
When PCIe-69814 boots, the driver accesses the calibration constants and is automatically 

set to hardware. In the absence of user assignment, the driver loads constants stored in 

bank 0. If constants from Bank 1 are to be loaded, the preferred bank can be designated 

as boot bank by software. Following re-assignment of the bank, the driver will load the 

desired constants on system reboot. This setting is recorded to EEPROM and is retained 

until reconfiguration.

A�2    Auto-Calibration 

Because  errors  in  measurement  and  outputs  will  vary  with  time  and  temperature,  re-

calibration is recommended when the module is installed. Auto-calibration can measure and 

minimize errors without external signal connections, reference voltages, or measurement 

devices. 

The  PCIe-69814  has  an  on-board  calibration  reference  to  ensure  the  accuracy  of  auto-

calibration. The reference voltage is measured on the production line and recorded in the 

on-board EEPROM.

Before initializing auto-calibration, it is recommended to warm up the PCIe-69814 for at 

least 20 minutes and remove connected cables. 

It is not necessary to manually factor delay into applications, as the PCIe-69814 

driver automatically adds the compensation time.

Содержание PCIe-69814 Series



































Отзывы: