JVD RB3383, Руководство пользователя

Страница: 31 / 47

Initial operation:
- According to the appearance of the Weather Station, the power adapter is inserted from the B10 position,
and the power supply of the power adapter is also noted.
- Open Weather Station battery compartment cover, open Weather Station battery compartment cover,
insert 2 x AA batteries observing polarity [ “+” and “–” marks].
- When you insert the batteries, all the icon on the LCD display will briefly light up for 3 seconds, and you will
hear a beep tone, and detect indoor temperature & humidity.
- The Weather Station will now start to make a connection to the outdoor remote sensor. This operation
takes about 3 minutes and is displayed by a flashing reception RF antenna symbol in the “
Outdoor sensor ”
display area on the receiver.
- This now, open Wireless Outdoor Sensor battery compartment cover, according to the channel to be set,
the channel of the sensor is set through the shift switch of the C6 position of the sensor, and Insert 2 x AA
batteries observing polarity [ “+” and “–” marks].
- When the wireless sensor is loaded into the battery, all the icon on the LCD display will briefly light up for 3
seconds, and detect the temperature and humidity of the sensor, At the same time, LED lights flicker once,
the wireless sensors automatically transmit wireless signals.
- When the Wireless Sensor is launched, the Weather Station alarm automatically receives its signal, and the
“ Outdoor sensor ” column displays the temperature and humidity values. At the same time, the number of
channels is shown in the icon of the sensor.
- The time of automatically receiving the wireless sensor signal after the weather station is started is 3
minutes. In 3 minutes, if all the channels are received, the radio control time receiving mode will be
automatically entered, and the backlight will be extinguished automatically.
F.Y.I.:
- The Weather Stations can receive up to 3 channels of wireless sensors.
- Note that when you enter the radio control time receiving mode, the backlight will automatically turn off.
This is a normal phenomenon. After the radio control time receiving reception, the backlight will be
automatically lit.
Reception of the Radio signal:
- The clock automatically starts the DCF signal search after 7 minutes of any restart or changing of new fresh
batteries. The radio mast icon starts to flash.
- At 1:00 /2:00 / 3:00, the clock automatically carries out the synchronization procedure with the DCF signal
to correct any deviations to the exact time. If this synchronization attempt is unsuccessful (the radio mast
icon disappears from the display), the system will automatically attempt another synchronization at the
next full one hour. This procedure is repeated automatically up to total 5 times.
- To start manual DCF signal reception, press and hold down the “
▲
” button for two seconds. If no signals
received within 7 minutes, then the DCF signal search stops (the radio mast icon disappears) and start again
at the next full one hour.
- During DCF radio signal reception, to stop searching radio signal, press and hold down the “
▲
” button for
two seconds.
F.Y.I.:
- A flashing radio mast icon indicates that the DCF signal reception has started.
- A continuously displayed radio mast icon indicates that the DCF signal was received successfully.
- The symbol " DST " indicating the time of receipt for daylight saving time.
- We recommend a minimum distance of 2.5 meters to all sources of interference, such as televisions or
computer monitors.
- Radio reception is weaker in rooms with concrete walls (e.g.: in cellars) and in offices. In such extreme
circumstances, place the system close to the window.
- During the DCF radio reception mode, only the “
▲
” button function, other button operations can only turn
on the backlight. If you want to perform other operation functions, press the “
▲
” button to exit the DCF
radio reception mode.
Manual time setting:
- Press and hold down the “ ” button for 2 seconds, the Button BEEP Sound Settings: ON or OFF, now
use “
▲
” and “
▼
” buttons to set BEEP in ON or OFF.
- Press “ ” to confirm your setting, the unit of temperature display starts to flash. Now use the “
▲
” and
“
▼
” button to set the temperature of the unit, the unit of temperature can be set to “°C” or “°F”