JVC RX-668VBK, Инструкция по эксплуатации

Страница: 22 / 43

20
Using the DVD MULTI Playback Mode
This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD
player. Before playing back a DVD, refer also to the manual supplied with the DVD player.
7. Press cursor control
@
/
#
to
adjust the left rear speaker output
level (from –10 to +10).
8. Press cursor control
%
/
fi
repeatedly until “REAR R
LEVEL” appears on the display.
9. Press cursor control
@
/
#
to
adjust the right rear speaker
output level (from –10 to +10).
From the remote control:
1. Press DVD MULTI so that “DVD
MULTI” appears on the display.
Note:
When you select “DVD MULTI” as the source to play, the DSP
mode is canceled temporarily, and the SURROUND button does
not work.
2. Select the analog discrete output
mode on the DVD player, and start
playing a DVD.
• Refer to the manual supplied with the DVD player.
If you need to make any adjustment, go to the following
steps.
3. Press SOUND CONTROL.
10 keys are activated for adjusting the sound.
4. Press CENTER – / + to adjust the
center speaker output level.
• Pressing CENTER – decreases the output
level up to –10 dB.
• Pressing increases the output
level up to +10 dB.
5. Press REAR•L – / + to adjust the
left rear speaker output level.
• Pressing REAR•L – decreases the output
level up to –10 dB.
• Pressing REAR•L + increases the output
level up to +10 dB.
6. Press REAR•R – / + to adjust the
right rear speaker output level.
• Pressing REAR•R – decreases the output
level up to –10 dB.
• Pressing REAR•R + increases the output
level up to +10 dB.
Activating the DVD MULTI Playback Mode
You can adjust the DVD MULTI playback mode while playing back
a DVD using the analog discrete output mode on the DVD player.
Once you made adjustments, the receiver memorizes the
adjustments until you change them. You also need to set the DVD
player to the analog discrete output mode.
Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 11).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• You can only adjust the rear and/or center speaker output levels
when you have connected rear speakers and/or a center speaker
and have set “REAR SPK” and/or “CENTER SPK” correctly. See
page 11.
On the front panel:
1. Press DVD MULTI so that “DVD
MULTI” appears on the display.
Note:
When you select “DVD MULTI” as the source to play, the DSP
mode is canceled temporarily, and the SURROUND button does
not work.
2. Select the analog discrete output mode on the
DVD player, and start playing a DVD.
• Refer to the manual supplied with the DVD player.
If you need to make any adjustment, go to the following
steps.
3. Press ADJUST so that the cursor
control
%
/
fi
/
@
/
#
buttons work
for adjusting the DVD MULTI
playback setting.
4. Press cursor control
%
/
fi
repeatedly until “CENTER
LEVEL” appears on the display.
5. Press cursor control
@
/
#
to
adjust the center speaker output
level (from –10 to +10).
6. Press cursor control
%
/
fi
repeatedly until “REAR L
LEVEL” appears on the display.
DVD MULTI
DVD M
ULT
I
ADJUST
SOUND
CONTROL
6 5
–
9 8
– REAR•L +
0 10
– REAR•R +
EN08_20.RX-668V[J]/f 99.1.16, 2:08 PM 20