10
Turning Off the Sounds
Temporarily—Muting
You can mute the sound temporarily.
Press MUTING
on the remote control
to mute
the sound through all speakers or headphones
connected.
• “MUTING” appears on the display and the volume
turns off (the volume level indicator goes off).
To restore the sound,
press MUTING again.
• Turning MASTER VOLUME on the front panel or pressing
/– on the remote control also restores the sound.
Changing the Display Brightness
You can dim the display.
Press DIMMER
on the remote control
.
• Each time you press the button, the display dims and
brightens alternately.
Turning Off the Power
with the Sleep Timer
You can fall asleep while listening to music—Sleep Timer.
Press SLEEP
on the remote control
repeatedly.
• The SLEEP indicator lights up on the display, and the
shut-off time changes in 10 minutes intervals.
When the shut-off time comes
The receiver turns off automatically.
To check or change the time remaining before the shut-off time
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly until
preferred remaining time appears on the display.
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 0 MIN” appears on the
display. (The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
Basic Operations
L
C
S.WFR
LS
RS
CH-
S
LFE
SPK
ANALOG
R
MUTING
DIMMER
Remote
ONLY
SLEEP
20
10
30
40
50
60
70
80
90
(Canceled)
0
L
C
S.WFR
LS
RS
CH-
S
LFE
SPK
SLEEP
ANALOG
R
Remote
ONLY
Basic adjustment auto memory
This receiver memorizes sound settings for each source when:
• Turning off the power,
• Changing the source, and
• Assigning the source name.
When you change the source, the memorized settings for the newly
selected source are automatically recalled.
Following can be stored for each source:
• Input attenuator mode (see page 15)
• Balance (see page 15)
• Tone adjustment (see page 15)
• Subwoofer output level (see page 15)
• Surround mode selection (see page 21-23)
Notes:
• You cannot assign and store different settings for digital input mode
and analog input mode.
• If the source is FM or AM, you can assign a different setting for
each band.
For recording
You can record any source playing through the receiver to a cassette
deck (or a CD recorder) connected to the TAPE/CDR jacks and the
VCR connected to the VCR jacks at the same time.
While recording, you can listen to the selected sound source at
whatever sound level you like without affecting the sound levels of
the recording.
Note:
The output level, tone adjustment (see page 15), and Surround
modes (see page 21-23) cannot affect the recording.
Signal and speaker indicators on the display
Signal indicators
Speaker indicators
The following signal indicators light up—:
L
: •
When digital input is selected:
Lights up when the left
channel signal comes in.
•
When analog input is selected:
Always lights up.
R
: •
When digital input is selected:
Lights up when the right
channel signal comes in.
•
When analog input is selected:
Always lights up.
C
:
When the center channel signal comes in.
LS :
When the left rear channel signal comes in.
RS :
When the right rear channel signal comes in.
S
:
When the monaural rear channel signal or 2 ch Dolby
Surround encoded signal comes in.
LFE:
When the
LFE
channel signal comes in.
The speaker indicators light up when both of the following
conditions are satisfied:
• The corresponding speaker is activated, and
• The corresponding speaker is required for the current playback.
Notes:
• When you select “DVD MULTI,” all signal indicators except “S” light
up.
• When “SUBWOOFER” is set to “YES” (see page 12),
S.WFR
lights
up.
Remote
ONLY
L
C
S.WFR
LS
RS
CH-
S
LFE
SPK
ONE TOUCH
PRO LOGIC
ΙΙ
DIGITAL AUTO
ANALOG
DIGITAL
LINEAR PCM
R
S.WFR
LS
RS
S
LFE
R
C
L
S.WFR
LS
RS
S
LFE
R
C
L
EN08-17.RX-6020V[J]_f
01.12.7, 2:03 PM
10
