background image

Caution: Proper Ventilation

To avoid risk of electric shock and fire and to protect from damage.
Locate the apparatus as follows:
Front:

No obstructions open spacing.

Sides:

No obstructions in 10 cm from the sides.

Top:

No obstructions in 10 cm from the top.

Back:

No obstructions in 15 cm from the back.

Bottom:

No obstructions, place on the level surface.

In addition, maintain the best possible air circulation as illustrated.

Attention: Ventilation Correcte

Pour éviter les chocs électriques, l’incendie et tout autre dégât.
Disposer l’appareil en tenant compte des impératifs suivants
Avant:

Rien ne doit gêner le dégagement

Flancs:

Laisser 10 cm de dégagement latéral

Dessus:

Laisser 10 cm de dégagement supérieur

Arrière:

Laisser 15 cm de dégagement arrière

Dessous:

Rien ne doit obstruer par dessous; poser l’appareil sur une
surface plate.

Veiller également à ce que l’air circule le mieux possible comme illustré.

Floor
Plancher

Stand height
15 cm or more
Hauteur du
socle: 15 cm ou
plus

Front
Avant

Spacing 15 cm or more
Dégagement de 15 cm ou plus

Wall or obstructions
Mur, ou obstruction

  CAUTION:         TO REDUCE THE RISK OF ELECTRIC SHOCK.
                         DO NOT REMOVE COVER (OR BACK)
                      NO USER SERVICEABLE PARTS INSIDE.
  REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, 
within an equilateral triangle is intended to 
alert the user to the presence of uninsulated 
"dangerous voltage" within the product's 
enclosure that may be of sufficient 
magnitude to constitute a risk of electric 
shock to persons.

The exclamation point within an equilateral 
triangle is intended to alert the user to the 
presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the appliance.

CAUTION

Caution –– STANDBY/ON

button!

Disconnect the mains plug to shut the power off completely. The
STANDBY/ON

 button in any position does not disconnect

the mains line. The power can be remote controlled.

Attention –– Commutateur STANDBY/ON

!

Déconnecter la fiche de secteur pour couper complètement le
courant. Le commutateur STANDBY/ON 

 ne coupe jamais

complètement la ligne de secteur, quelle que soit sa position.  Le
courant peut être télécommandé.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1.

Do not remove screws, covers or cabinet.

2.

Do not expose this appliance to rain or moisture.

ATTENTION

Afin d’éviter tout risque d’électrocution, d’incendie, etc.:

1.

Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.

2.

Ne pas exposer l’appareil à la pluie ni à l’humidité.

Warnings, Cautions and Others/
Mises en garde, précautions et indications diverses

RX-5020VBK
RX-5022VSL

WARNING: TO REDUCE THE RISK OF FIRE 
OR ELECTRIC SHOCK, DO NOT EXPOSE 
THIS APPLIANCE TO RAIN OR MOISTURE.

For the main unit:

This equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the 
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that 
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the 
manufacturer for compliance could void the user’s authority to 
operate the equipment.

 For Canada/pour le Canada

CAUTION: 

TO PREVENT ELECTRIC SHOCK, MATCH WIDE 

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT

ATTENTION: 

POUR EVITER LES CHOCS ELECTRIQUES, 

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA 
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER 
JUSQUAU  FOND

For Canada/pour Le Canada

THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS
B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,”
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS RADIOELECTRIQUES APPLICABLES AUX
APPAREILS NUMERIQUES DE CLASSE B PRESCRITES
DANS LA NORME SUR LE MATERIEL BROUILLEUR;
“APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE
MINISTRE DES COMMUNICATIONS.

RX-5020-5022V[C]_Safety_f

01.12.27, 10:14 AM

1

Содержание RX-5020VBK









































































Отзывы: