JVC KD-R301, Инструкция по эксплуатации

Страница: 57 / 148

3 – EN
INSTRUCTIONS
Audio amplifier section
Maximum Power Output:
Front/Rear: 50 W per channel
Continuous Power Output (RMS):
Front/Rear: 19 W per channel into 4 Ω, 40 Hz
to 20 000 Hz at no more than 0.8%
total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range: Bass: ±12 dB at 100 Hz
Treble: ±12 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Output Impedance: 1 kΩ
Other Terminal: AUX (auxiliary) input jack
Tuner section
Frequency Range:
FM: 87.5 MHz to 108.0 MHz
AM: 531 kHz to 1 602 kHz
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω)
50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω)
Alternate Channel Selectivity (400 kHz): 65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 30 dB
[AM Tuner]
Sensitivity/Selectivity: 20 μV/35 dB
SPECIFICATIONS
CD player section
Type: Compact disc player
Signal Detection System: Non-contact optical pickup
(semiconductor laser)
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range: 93 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
[For KD-R304]
MP3 Decoding Format: MPEG1/2 Audio Layer 3
Max. Bit Rate: 320 kbps
WMA (Windows Media® Audio) Decoding Format:
Max. Bit Rate: 192 kbps
General
Power Requirement:
Operating Voltage: DC 14.4 V (11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature: 0°C to +40°C
Dimensions (W × H × D):
Installation Size (approx.):
182 mm × 52 mm × 160 mm
Panel Size (approx.):
188 mm × 58 mm × 6 mm
Mass (approx.):
1.3 k g (excluding accessories)
Design and specifications are subject to change without
notice.
TROUBLESHOOTING
Symptoms Remedies/Causes
General
• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.
• Check the cords and connections.
• This unit does not work at all. Reset the unit.
• “AUX IN” cannot be selected. Check the “
SRC SELECT
”
=
“
AUX IN
” setting (see “Menu
operations”).
FM/AM
• SSM automatic presetting does not work. Store stations manually.
• Static noise while listening to the radio. Connect the antenna firmly.
• “AM” cannot be selected. Check the “ SRC SELECT ”
=
“ AM ” setting (see “Menu
operations”).
Disc playback
• Disc cannot be played back. Insert the disc correctly.
• CD-R/CD-RW cannot be played back.
• Tracks on the CD-R/CD-RW cannot be
skipped.
• Insert a finalized CD-R/CD-RW.
• Finalize the CD-R/CD-RW with the component which you used for
recording.
• Disc can be neither played back nor
ejected.
• Unlock the disc.
• Eject the disc forcibly.
• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.
• Change the disc.
• Check the cords and connections.
• “NO DISC” appears on the display. Insert a playable disc into the loading slot.
• “PLEASE” and “EJECT” appear alternately
on the display.
Press
0
, then insert a disc correctly.
MP3/WMA playback (for KD-R304)
• Disc cannot be played back. • Use a disc with MP3/WMA tracks recorded in a format compliant
with ISO 9660 Level 1, Level 2, Romeo, or Joliet.
• Add the extension code <.mp3> or <.wma> to the file names.
• Noise is generated. Skip to another track or change the disc. (Do not add the extension
code <.mp3> or <.wma> to non-MP3 or WMA tracks.)
• A longer readout time is required
(“READING” keeps flashing on the display).
Do not use too many hierarchical levels and folders.
• Tracks are not played back in the order you
have intended.
Playback order is determined when the files are recorded.
• The elapsed playing time is not correct. This sometimes occurs during playback. This is caused by how the
tracks are recorded on the disc.
• The correct characters are not displayed
(e.g. album name).
This unit can only display letters (upper case), numbers, and a
limited number of symbols.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.
Sound adjustments
* You can change “
USER
” settings and store as your own sound mode (see below).
Storing your own sound mode
Title assignment
You can assign titles to 30 station frequencies (FM and AM) using 8 characters (maximum) for each title.
To erase the entire title
In step 2 above...
Menu operations
Menu items Selectable settings
DEMO
DEMO • DEMO ON : The display demonstration will be activated automatically if no operation is done for
about 20 seconds.
• DEMO OFF : Cancels.
CLOCK
CLOCK DISP * 1 • CLOCK ON : The clock time is shown on the display at all times when the power is turned off.
• CLOCK OFF : Cancels; pressing DISP will show the clock time for about 5 seconds when the power
is turned off.
CLOCK SET : Adjust the hour, then the minute. [Initial: 1:00]
EQ
EQ : Select a preset sound mode suitable to the music genre.
USER, ROCK, CLASSIC, POPS, HIP HOP, JAZZ
DISPLAY
DIMMER • DIMMER ON : Dims the display and button illumination.
• DIMMER OFF : Cancels.
SCROLL * 2 • SCROLL ONCE : Scrolls the displayed information once.
• SCROLL AUTO : Repeats scrolling (at 5-second intervals).
• SCROLL OFF : Cancels.
Pressing DISP for more than one second can scroll the display regardless of the setting.
TAG DISPLAY
(for KD-R304) • TAG ON : Shows the Tag information while playing MP3/WMA tracks.
• TAG OFF : Cancels.
TUNER
MONO * 3 • MONO ON : Activate monaural mode to improve FM reception, but stereo effect will be lost.
• MONO OFF : Restore the stereo effect.
IF BAND • AUTO : Increases the tuner selectivity to reduce interference noises between adjacent stations.
(Stereo effect may be lost.)
• WIDE : Subject to interference noises from adjacent stations, but sound quality will not be
degraded and the stereo effect will remain.
AUDIO
FADER * 4 R06 – F06 : Adjust the front and rear speaker output balance. [Initial: 00]
BALANCE L06 – R06 : Adjust the left and right speaker output balance. [Initial: 00]
LOUD • LOUD OFF : Cancels.
• LOUD ON : Boost low and high frequencies to produce a well-balanced sound at a low volume
level.
AUX ADJUST AUX ADJ 00 – AUX ADJ 05 : Adjust the auxiliary input level to avoid the sudden increase of the
output level when changing the source to external component connected to the AUX input jack on
the control panel.
*
1
If the power supply is not interrupted by turning off the ignition key of your car, it is recommended to select “ CLOCK
OFF ” to save the car’s battery.
*
2
Some characters or symbols will not be shown correctly (or will be blanked) on the display.
* 3 Displayed only when the source is “FM.”
* 4 If you are using a two-speaker system, set the fader level to “00.”
Preset values
SETTINGS
Select “
EQ
”
Indication (For)
BASS
TREBLE
LOUD
USER (Flat sound) 00 00 OFF
ROCK (Rock or disco music) +03 +01 ON
CLASSIC (Classical music) +01 –02 OFF
POPS (Light music) +04 +01 OFF
HIP HOP (Funk or rap music) +02 00 ON
JAZZ (Jazz music) +02 +03 OFF
Select “
USER
” for “
EQ.
”
This mode will be canceled if
no operation is done for about
30 seconds.
1 Select a tone.
BASS
Ô
TREBLE
2
Adjust the Lever.
–06 to +06
3
Repeat
1
and
2
for the
other tone if necessary.
Select “FM” or “AM.”
Show the title entry screen.
Select a character.
Move to the next (or previous) character
position.
Repeat steps 1 and 2 until you finish entering
the title.
Finish the procedure.
Menu items Selectable settings
AUDIO
BEEP • BEEP ON : Activates the keypress tone.
• BEEP OFF : Deactivates the keypress tone.
AMP GAIN * 5 • HIGH POWER : VOLUME 00 – VOLUME 50
• LOW POWER : VOLUME 00 – VOLUME 30 (Select if the maximum power of each speaker is less
than 50 W to prevent damaging the speaker.)
SRC SELECT
AM *
6
• AM OFF : Disable “AM” in source selection.
• AM ON : Enable “AM” in source selection.
AUX IN
* 7
• AUX OFF : Disable “AUX IN” in source selection.
• AUX ON : Enable “AUX IN” in source selection.
* 5
The volume level automatically changes to “VOLUME 30” if you change to “
LOW POWER
” with the volume level is set
higher than “VOLUME 30.”
* 6
Displayed only when any source other than “AM” is selected.
* 7 Displayed only when any source other than “AUX IN” is selected.
Initial: Underlined
or
Initial: Underlined
While “ USER ”
is shown on
the display...
Repeat step 2 if necessary.
• To return to the previous menu, press
BACK.
EN_KD-R304_R204[UI]_f.indd 3 EN_KD-R304_R204[UI]_f.indd 3 3/9/08 9:36:49 AM 3/9/08 9:36:49 AM