JVC KD-G115, Инструкция по эксплуатации

Страница: 21 / 66

KD-G116/KD-G115
Installation/Connection Manual
°“√µ‘¥µ—Èß/§ŸË¡◊Õ°“√µ‘¥µ—Èß
GET0252-004A
[U/UH]
1004DTSMDTJEIN
EN, TH
ENGLISH
This receiver is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If
your vehicle does not have this system, a voltage inverter is required, which can be purchased
at JVC car audio dealers.
‰∑¬
™ÿ¥ª√–°Õ∫π’ȉ¥È√—∫°“√ÕÕ°·∫∫¡“‡æ◊ËÕ„™Èß“π°—∫√–∫∫ °√–· ‰øøÈ“ “¬¥‘π¢—È«≈∫°√–· µ√ß
12
‚«≈∑Ï À“°√∂¬πµÏ¢Õߧÿ≥‰¡Ë‰
¥È„™È√–∫∫π’È µÈÕß„™È‡§√◊ËÕß·ª≈ß°√–· ‰ø™Ë«¬ ´÷Ëß “¡“√∂À“´◊ÈÕ‰¥È®“°√È“π¢“¬‡§√◊ËÕ߇ ’¬ß√∂¬πµÏ
JVC
J
Handles
§—π∫—ߧ—∫
F
Washer (ø5)
ª√–‡°Áπ«ß·À«π
(ø5
)
G
Lock nut (M5)
πÕµ≈ÁÕ§ (
M5
)
H
Mounting bolt (M5 x 20 mm)
≈—°µ‘¥ (
M5 x 20
¡‘≈≈‘‡¡µ√)
I
Rubber cushion
¬“ß°—π°√–·∑°
A
/
B
Hard case/Control panel
≈—ß∫√√®ÿ/ÀπÈ“ª—¥
D
Trim plate
·ºËπ‚≈À–¢Õ∫·µËß
E
Power cord
“¬‡§‡∫‘≈°”≈—ß
Parts list for installation and connection
The following parts are provided for this receiver.
After checking them, please set them correctly.
√“¬°“√ Ë«πª√–°Õ∫ ”À√—∫µ‘¥µ—Èß·≈–‡™◊ËÕ¡µËÕ°—π
«πª√–°Õ∫µËÕ‰ªπ’È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È À≈—ß®“°µ√«® Õ∫·≈È« ª√—∫µ—È߇§√◊ËÕß„ÀÈ∂Ÿ°µÈÕß
1
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require
information regarding installation kits, consult your JVC car audio dealer or a company supplying
kits.
• If you are not sure how to install this receiver correctly, have it installed by a qualified
technician.
°“√µ‘¥µ—Èß (°“√ª√–°Õ∫·ºßÀπÈ“ª—∑¡Ï‡¢È“)
¿“æµ—«Õ¬Ë“ßµËÕ‰ªπ’È· ¥ß∂÷ß°“√µ‘¥µ—Èß·∫∫∑—Ë«‰ª À“°§ÿ≥¡’ª—≠À“À√◊ÕµÈÕß°“√¢ÈÕ¡Ÿ≈‡°’ˬ«°—∫™ÿ¥µ‘¥µ—Èß °√ÿ≥“ª√÷°…“°—∫ºŸÈ¢“¬‡§√◊ËÕ߇ ’
¬ß√∂¬πµÏ
JVC
¢Õß∑Ë“πÀ√◊Õ∫√‘…—
•
™ÿ¥ª√–°Õ∫ ∂È“§ÿ≥‰¡Ë·πË„®«Ë“µ‘¥µ—Èß™ÿ¥ª√–°Õ∫π’È∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë „ÀÈÀ“™Ë“ߺŸÈ‡™’ˬ«™“≠‡ªÁπºŸÈµ‘¥µ—Èß
Do the required electrical connections.
µËÕ
“¬‰øµ“¡∑’Ë°”À𥉫È∑—ÈßÀ¡¥
*
1
When you stand the receiver, be
careful not to damage the fuse on
the rear.
*
1
‡¡◊ËÕ§ÿ≥µ—Èß™ÿ¥ª√–°Õ∫¢÷Èπ √–«—ßլ˓∑”„ÀÈø‘«
Ï∫√‘‡«≥
Ë«π∑È“¬‡ ’¬À“¬
Bend the appropriate tabs to hold the
sleeve firmly in place.
ßÕ·ºËπ‡æ◊ËÕ¬÷¥ª≈Õ°„ÀȵËÕ°—π‡¢È“∑’Ë
Removing the receiver
Before removing the receiver, release the rear section.
When installing the receiver without using the sleeve /
‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫‚¥¬‰¡Ë„™Èª≈Õ°ÀÿÈ¡
In a Toyota for example, first remove the car radio and install the receiver in its place.
µ—«Õ¬Ë“߇™Ëπ „π√∂¬πµÏ‚µ‚¬µÈ“ „ÀÈ∂Õ¥«‘∑¬ÿµ‘¥√∂¬πµÏÕÕ°°ËÕπ·≈–µ‘¥µ—Èß™ÿ¥ª√–°Õ∫π’ȇ¢È“‰ª·∑π
When using the optional stay /
‡¡◊ËÕ„™Èµ—«¬÷¥·∫∫‡≈◊Õ°‰¥È
Note : When installing the receiver on the mounting bracket, make sure to use the 8 mm-long screws. If
longer screws are used, they could damage the receiver.
À¡“¬‡Àµ
:
‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫≈ß„π·∑Ëπ√Õß√—∫‰«È „ÀÈ„™È °√Ÿ¬“«¢π“¥
8
¡‘≈≈‘‡¡µ√ ∂È“„™È °√Ÿ¬“«°«Ë“π’ÈÕ“®∑”„ÀÈ™ÿ¥ª√–°Õ∫‡ ’¬À“¬‰¥ô
Bracket*
·∑Ëπ√Õß√—∫
*
Bracket*
·∑Ëπ√Õß√—∫
*
* Not included for this receiver.
*
‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π
Flat type screws
(M5 x 8 mm)*
°√ŸÀ—«‡√’¬∫
(
M5 x 8
¡‘≈≈‘‡¡µ√)
*
Pocket
°–‡ª“–
Flat type screws
(M5 x 8 mm)*
°√ŸÀ—«‡√’¬∫
(M5 x 8
¡‘≈≈‘‡¡µ√
)*
Screw (option)
°√Ÿ (‡≈◊Õ°‰¥È)
Stay (option)
µ—«¬÷¥ (‡≈◊Õ°‰¥È)
Fire wall
ºπ—ß°—π‰ø
Dashboard
·ºßÀπÈ“ª—∑¡á
Install the receiver at an angle of less than 30˚.
µ‘¥µ—Èß™ÿ¥ª√–°Õ∫∑’Ë¡ÿ¡µË”°«Ë“
30
Õß»“
TROUBLESHOOTING
•
The fuse blows.
* Are the red and black leads connected correctly?
•
Power cannot be turned on.
* Is the yellow lead connected?
•
No sound from the speakers.
* Is the speaker output lead short-circuited?
•
Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
•
Noise interfere with sounds.
* Is the rear ground terminal connected to the carʼs chassis using shorter and thicker cords?
•
Receiver becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
•
This receiver does not work at all.
* Have you reset your receiver?
°“√µ√«® Õ∫ª—≠À“¢—¥¢ÈÕß
•
ø‘« Ï¢“¥
*
¡’°“√‡™◊ËÕ¡ “¬µ–°—Ë« ’¥”·≈– ’·¥ßլ˓ß∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë
•
‰¡Ë “¡“√∂‡ª‘¥‡§√◊ËÕ߉¥È
*
¡’°“√‡™◊ËÕ¡ “¬µ–°—Ë« ’‡À≈◊ÕßÀ√◊Õ‰¡Ë
•
‰¡Ë¡’‡ ’¬ßÕÕ°®“°≈”‚æß
*
“¬µ–°—Ë« «π∑’ËÕÕ°∑“ß≈”‚æ߇°‘¥‰øøÈ“≈—¥«ß®√À√◊Õ‰¡Ë
•
‡ ’¬ß‡æ’Ȭπ
*
“¬µ–°—Ë« «π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ߥ‘πÀ√◊Õ‰¡Ë
*
“¬¢—È«≈∫
“–”
¢Õß≈”‚æߥȓπ´È“¬·≈–¢«“µËÕ≈ߥ‘πµ“¡ª°µ‘À√◊Õ‰¡Ë
•
‡ ’¬ß√∫°«π
*
¡’°“√„™È “¬ —ÈπÊ À√◊ÕÀπ“Ê µËÕ®“°‡§√◊ËÕß «π∑’˵‘¥µ—Èß ‰«È∫πæ◊Èπ¥È“πÀ≈—ß°—∫µ—«∂—ß√∂¬πµÏÀ√◊Õ‰¡Ë
•
™ÿ¥ª√–°Õ∫√ÈÕπ¢÷Èπ
*
“¬µ–°—Ë« Ë«π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ߥ‘πÀ√◊Õ‰¡Ë
*
“¬¢—È«≈∫
“–”
¢Õß≈”‚æߥȓπ´È“¬·≈–¢«“µËÕ≈ߥ‘πµ“¡ª°µ‘À√◊Õ‰¡Ë
•
‡§√◊ËÕß√—∫π’È∑”ß“π‰¡
*
∑Ë“π‰¥Èµ—È߇§√◊ËÕß„À¡Ë·≈È«À√◊Õ¬—ß
C
Sleeve
ª≈Õ°ÀÿÈ¡
°“√∂Õ¥™ÿ¥ª√–°Õ∫
°ËÕπ®–∂Õ¥™ÿ¥ª√–°Õ∫ „ÀȪ≈¥ÀπÈ“µ—¥ Ë«π∑È“¬°ËÕπ
Insert the two handles, then pull them as illustrated so
that the receiver can be removed.
„ ˧—π∫—ߧ—∫
2
Õ—π≈ß„π√ËÕß ”À√—∫„™Èæ—π≈«¥ ¥—ß¿“æ ®“°π—Èπ „Àȇ≈◊ËÕπ™ÿ¥ª√–
°Õ∫ÕÕ° „π¢≥–∑’˧ËÕ¬ Ê ¥÷ߧ—π∫—ߧ—∫∑—Èß Õß Õ—πÕÕ°®“°°—π
Instal1-2_KD-G116[U_UH]1.indd 1 10/14/04 7:01:40 PM