JVC InteriArt HV-28P37SJE Скачать руководство пользователя страница 31

Страница: 31 / 43

(No.YA010)1-31

4.8

ADJUSTMENT PROCEDURE

4.8.1 CHECK ITEM

4.8.2 HIGH VOLTAGE

4.8.3 HORIZONTAL FREQUENCY

Item

Measuring

instrument

Test point

Adjustment part

Description

B1 POWER
SUPPLY
check

Signal
generator

DC voltmeter

Remote
control unit

S1 Connector
TP-91
TP-E
[MAIN PWB]

[2. V/C]
1. CUT_OF_R

SCREEN VR
[In FBT]

(1) Receive the black and white signal (color off).
(2) Connect the DC voltmeter to TP-91 (S1 connector 5

pin) and TP-E (S1 connector 1 pin).

(3) Select 2. V/C.
(4) Select < 1. CUT_OF_R >.
(5) Show one horizontal line with the [YELLOW (FREEZE/

SWAP)] key.

(6) Turn the SCREEN VR counterclockwise to display

whole black screen.

(7) Make sure that the voltage is DC148V (±2V).
(8) Readjust the SCREEN VR to appear the horizontal

line faitly, and cancel the horizontal line by pressing
the [YELLOW (FREEZE/SWAP)] key.

Item

Measuring

instrument

Test point

Adjustment part

Description

HIGH VOLTAGE

Signal
generator

HV voltmeter

Remote
control unit

CRT anode

[2. V/C]
1. CUT_OF_R

EHT ADJ VR (R2528)
[EHT PWB]

SCREEN VR
[In FBT]

(1) Receive the black and white signal (color off).
(2) Connect the HV voltmeter to CRT anode and

chassis GND.

(3) Select 2. V/C.
(4) Select < 1. CUT_OF_R >.
(5) Show one horizontal line with the [YELLOW (FREEZE/

SWAP)] key.

(6) Turn the SCREEN VR counterclockwise to display

whole black screen.

(7) Adjust EHT ADJ VR so that the voltage become

31kV (±0.2V).

(8) Readjust the SCREEN VR to appear the horizontal

line faitly, and cancel the horizontal line by pressing
the [YELLOW (FREEZE/SWAP)] key.

Item

Measuring

instrument

Test point

Adjustment part

Description

HORIZONTAL
FREQUENCY

Remote
control unit

[4. DEF]
1. FREE-RUN

(1) Receive any broadcast.
(2) Select 4. DEF.
(3) Confirm that when you enter to the 4. DEF, the

screen automatically show the FREE-RUN screen.
And the picture run up or down.

(4) Adjust the < 1. FREE-RUN > to stop the picture. But

the picture does not stop completely.

(5) Press the [MENU] key to memorize the adjustment

data.

Содержание InteriArt HV-28P37SJE












































Результаты поиска

Содержание InteriArt HV-28P37SJE

Отзывы:

Похожие инструкции для InteriArt HV-28P37SJE

Бренды по названию

Популярные бренды

JVC InteriArt HV-28P37SJE, Руководство по обслуживанию

Результаты поиска

Содержание InteriArt HV-28P37SJE

Отзывы:

Похожие инструкции для InteriArt HV-28P37SJE

Бренды по названию

Популярные бренды