1-8
-0
-7
-
Initial value
-1
-0
-
EJECT position
-
-
-0
EJECT position (Cassette housing drive mode)
-2
-7
-
Housing operating
-
-
-1
Between EJECT and U / L STOP
-3
-1
-2
U / L STOP position
-
-
-3
Guide arm drive position
-4
-7
-4
Tape being loaded / unloaded (When the pole base is
located on the front side of the position just beside the
drum)
-5
-2
-5
Tape being loaded / unloaded (When the pole base is
located on the rear side of the position just beside the
drum)
-6
-7
-6
Pole base compressed position
-7
-3
-F
FF / REW position
-8
-7
-F
Between FF / REW and STOP with pinch roller compres-
sion ON
-9
-4
-F
STOP with pinch roller compression OFF
-A
-7
-E
Between STOP with pinch roller compression OFF and
REV
-B
-5
-
REV (REV STILL / SLOW) position
-
-
-D
REV position
-
-
-C
Between REV and REV STILL / SLOW
-
-
-B
REV STILL / SLOW position
-C
-7
-
Between REV and FWD
-
-
-A
Between REV STILL / SLOW and FWD STILL / SLOW
-D
-6
-
FWD (FWD STILL / SLOW) position
-
-
-9
FWD STILL / SLOW position
-E
-7
-
Between FWD and PLAY
-
-
-8
Between FWD STILL / SLOW and PLAY
-F
-6
-7
PLAY position
0-
VHS
Cassette insertion
Tab broken
ON
ON
1-
VHS
Cassette insertion
Tab broken
ON
OFF
2-
VHS
Cassette insertion
Tab broken
OFF
ON
3-
VHS
Cassette insertion
Tab broken
OFF
OFF
4-
VHS
Cassette insertion
Tab present
ON
ON
5-
VHS
Cassette insertion
Tab present
ON
OFF
6-
VHS
Cassette insertion
Tab present
OFF
ON
7-
VHS
Cassette insertion
Tab present
OFF
OFF
8-
S-VHS
Cassette ejection
Tab broken
ON
ON
9-
S-VHS
Cassette ejection
Tab broken
ON
OFF
A-
S-VHS
Cassette ejection
Tab broken
OFF
ON
B-
S-VHS
Cassette ejection
Tab broken
OFF
OFF
C-
S-VHS
Cassette ejection
Tab present
ON
ON
D-
S-VHS
Cassette ejection
Tab present
ON
OFF
E-
S-VHS
Cassette ejection
Tab present
OFF
ON
F-
S-VHS
Cassette ejection
Tab present
OFF
OFF
3– : Mechanism sensor information
[Common table of MN*, HD* and M3*]
Mechanism sensor information
Display MN* / HD*
M3*
REC safety
Start
End
S-VHS SW
CASS SW
SW
sensor
sensor
* 6 : Cassette tape winding position
The cassette tape winding position at the moment of EMG is
displayed by dividing the entire tape (from the beginning to the
end) in 22 sections using a hex number from “00” to “15”.
“00”
: End of winding
“15”
: Beginning of winding
“FF or – – ” : Tape position not identified
–4 : Mechanism mode position
[Common table of MN*, HD* and M3*]
Display
Mechanism mode position
MN* HD* M3*
Note:
•
The values of cassette tape type <2> in the above table
are typical values with representative cassette tapes.
* 7 : Cassette tape type <2> (Winding area)
Display
Cassette tape type <2>
00
Cassette type not identified
07
Small reel, thick tape
T-5
08 - 0E
C cassette, thick tape
TC-10
09 - 15
C cassette, thick tape
TC-20P
0A - 0B
Small reel, thick tape
T-20
0A - 16
C cassette, thin tape
TC-30
0A - 16
C cassette, thin tape
TC-40
0D - 0F
Small reel, thick tape
T-40
11 - 14
Small reel, thick tape
T-60
15 - 18
Small reel, thick tape
T-80 / DF-160
17 - 1A
Small reel, thick tape
T-90 / DF-180
19 - 1D
Small reel, thick tape
T-100
1D - 21
Small reel, thick tape
T-120 / DF-240
1E - 1F
Small reel, thin tape
T-140
1F - 23
Small reel, thick tape
T-130
21 - 23
Small reel, thin tape
T-160
21 - 23
Small reel, thin tape
T-168
22 - 24
Small reel, thick tape
DF-300
22 - 24
Small reel, thin tape
T-180 / DF-360
22 - 24
Small reel, thin tape
T-210 / DF-420
22 - 23
Large reel
T-5
23 - 24
Large reel
T-10
25 - 26
Large reel
T-20
27 - 29
Large reel
T-30
29 - 2B
Large reel
T-40
2D - 2F
Large reel
T-60
Notes:
•
Cassette tape type
<1> is identified a few times during mode
transition and the identification count is variable depending on
the cassette tape type. If an EMG occurs in the middle of identi-
fication, the cassette tape type may not be able to be identified.
•
If other value than those listed in the above table is displayed,
the cassette tape type is not identified.
Display
Cassette tape type <1>
00
Cassette type not identified
16
Large reel/small reel (T-0 to T-15/T-130 to T-210) not classified
82
Small reel, thick tape (T-120) identified/thin tape (T-140) identified
84
Large reel (T-0 to T-60) identified
92
Small reel, thick tape (T-130) identified/thin tape (T-160 to T-210) identified
93
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) not classified
C3
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) being classified
D3
Small reel, thick tape/C cassette (T-0 to T-100/C cassette) being classified
E1
C cassette, thick tape (TC-10 to TC-20) identified
E2
Small reel, thick tape (T-0 to T-100) identified
E9
C cassette, thin tape (TC-30 to TC-40) identified
F1
C cassette, thick tape/thin tape (TC-10 to TC-40) not classified
* 5 : Cassette tape type <1>
Note:
• EMG detail information <2> is the reference information
stored using the remaining tape detection function of the
cassette tape. As a result, it may not identify cassette cor-
rectly when a special cassette tape is used or when the
tape has variable thickness.
1.8.5
EMG detail information <2>
The type of the cassette tape and the cassette tape winding po-
sition can be confirmed based on the figure in EMG detail infor-
mation <2> .
[FDP/OSD display]
* 5 : * 6 : * 7
* 5 : Type of the cassette tape in use <1>
* 6 : Winding position of the cassette tape in use
* 7 : Type of the cassette tape in use <2> (Winding area)
Note:
• In the case of the "HD*” microprocessor, as the display is
always "-7” at any intermediate position between modes,
the position of transitory EMG may sometimes not be lo-
cated.
