JVC GY-HM850CHE, Инструкция по эксплуатации

Страница: 129 / 220

CH1 Filter to CH4 Filter
For setting the input signals for [CH-1] to [CH-4]
respectively to Wind Cut, Equalizer, or Off.
[Setting Values: Equalizer, Wind Cut,
R
Off]
Memo :
0
If the [AUDIO INPUT] signal selection switch 1
setting of [CH-1] in the [CH1 Filter] item is set to
“LINE”, “Off” is displayed and selection is
disabled.
0
When [CH2 Filter] is set as follows, “Off” is
displayed and selection is disabled.
0
When [CH-2] is set to “INPUT1”, and the
[AUDIO INPUT] signal selection switch 1
setting is set to “LINE”
0
When [CH-2] is set to “INPUT2”, and the
[AUDIO INPUT] signal selection switch 2
setting is set to “LINE”
0
If the [AUDIO INPUT] signal selection switch 1
setting of [CH-3] in the [CH3 Filter] item is set to
“LINE”, “Off” is displayed and selection is
disabled.
0
When [CH4 Filter] is set as follows, “Off” is
displayed and selection is disabled.
0
When [CH-4] is set to “INPUT1”, and the
[AUDIO INPUT] signal selection switch 1
setting is set to “LINE”
0
When [CH-4] is set to “INPUT2”, and the
[AUDIO INPUT] signal selection switch 2
setting is set to “LINE”
Equalizer
You can correct the characteristic and enhance the
sound of the connected microphone using this
equalizer setting.
For setting the audio frequency from a 5-band
equalizer.
0
Frequency:
100Hz, 330Hz, 1kHz, 3.3kHz, 10kHz
0
Variable level:
± 6dB (0.5dB step)
Memo :
0
Audio will be recorded in the characteristic set
in the equalizer.
0
Set all bands to “0dB” to bypass the equalizer.
0
When the equalizer level is set to the + side, the
audio may be distorted. In this case, reduce the
recording level in Manual mode.
0
If the values of multiple frequencies are
changed, the specified levels and the actual
levels may be different due to interference
between the frequency bands.
0
Not selectable if none of the items from [CH1
Filter] to [CH4 Filter] is set to “Equalizer”.
Output CH
For setting the channel to output to the [AUDIO
OUTPUT] and [HDMI] terminals.
0
CH3/4:
Outputs the audio of [CH-3] and [CH-4].
0
CH1/2:
Outputs the audio of [CH-1] and [CH-2].
0
SW Set:
Outputs according to the [MONITOR SELECT]
switch setting.
[Setting Values: CH3/4,
R
CH1/2, SW Set]
Monitor
For setting the audio sound of the [PHONES]
terminal to stereo or mixed sound when the
[MONITOR] selection switch on the LCD monitor is
set to “BOTH”.
0
Mix:
Outputs mixed sound (mixed sound of CH-1 and
CH-2) to both L and R.
0
Stereo:
Outputs stereo sound (outputs audio sound of
CH-1 to L, and CH-2 to R).
[Setting Values:
R
Mix, Stereo]
Memo :
0
When the [MONITOR SELECT] switch is set to
a value other than “BOTH”, “---” is displayed and
selection is disabled.
Alarm Level
For selecting whether to turn on the warning tone
as well as setting the volume.
The warning tone is output from the monitor
speaker or [PHONES] terminal.
[Setting Values: Off, 1 to 5] (
R
5)
Test Tone
For specifying whether to output the audio test
signals (1 kHz) during color bar output.
[Setting Values: On,
R
Off]
A/V Set Menu
129
Menu
Display and
D
etailed
S
etti
ngs