12
Estimated Recordable Time of SD
Cards
The estimated recordable time is only a
guide. Differences may occur depending on
the SD card in use and the battery condition.
Slide the write-protect switch upward to
enable writing or deleting.
Slide the write-protect switch downward to
prevent writing or deleting. (Images in the
card are protected)
Video
Outputs
4K Single Fiber Optic Output
The 4K single fiber optic output transmits up
to 3840x2160 progressive, 59.94 frames
per second video. The data is sent via a
single fiber by Wavelength Division
Multiplexing (WDM) the four 1920x1080
quadrants of the 3840x2160 video via
SMPTE
ST
424 Compliant 3G-SDI.
The optical output conforms to the IEC
60825-1 Classification, the “Eye Safe”
certification for laser transmission
equipment.
Please contact AltaSens for further
information and for assistance to identify or
purchase compatible equipment that will
work with this single fiber 4K optical format.
WRITE-PROTECT SWITCH
WRITE/DELETE ENABLED
WRITE/DELETE DISABLED
The ProCam UHD has a single fiber optic and
a HD-SDI monitor output. Connect an
appropriate device to each output, observing
the following specifications:
HD-SDI Monitor Output
Write-Protect Switch on the SD Card
Control
Connector
Inputs
The ProCam UHD features a multi-function
control input on the 9-pin D-sub connector.
This connector contains several features,
including serial communication to and from
the camera for external control, genlock
input, and 12-15 V output to power external
controllers. The Control connector’s pinout is
shown below
5
1
9
6
The HD-SDI monitor output is 1920x1080,
interlaced. The frame rate is dependent upon
the frequency of main output.
Note:
Test pattern output for this unit is
currently only available in single fiber
optic output at this time. HD-SDI monitor
output is not available.
Use cable at a length of < 100 meters
Not guaranteed to connect to all
appliances
Caution
:
The controller which ProCam UHD will
provide power supply is limited to below
1A.
PIN DIRECTION DESCRIPTION
1
―
Not Used
2
OUT
Data from Camera
3
IN
Serial Data to Camera
4
―
Not Used
5
―
Ground
6
IN
Genlock
Sync Signal
7
―
Not Used
8
―
Ground
9
OUT
12-15 Volts
D-SUB
9
FEMALE
CONNECTOR
ON
BACK
OF
CAMERA
CAPACITY
QUICK
TIME
4K
16 GB
(UHS
SPEED
CLASS
3)
12 min
32 GB
(UHS
SPEED
CLASS
3)
25 min
64 GB
(UHS
SPEED
CLASS
3)
50 min
128 GB
(UHS
SPEED
CLASS
3)
100 min
16
Not Used
The 4K Camera Module features a multi-
function control input on the 9-pin D-sub
connector. This connector contains several
features, including serial communication to
and from the camera for external control and
12-15 V output to power external controllers.
The Control connector’s pinout is shown
below.
The controller which the 4K Camera
Module will provide power supply is
limited to below 1A.
Estimated Recordable Time of SD
Cards
The estimated recordable time is only a
guide. Differences may occur depending on
the SD card in use and the battery condition.
Slide the write-protect switch upward to
enable writing or deleting.
Slide the write-protect switch downward to
prevent writing or deleting. (Images in the
card are protected)
Video
Outputs
4K Single Fiber Optic Output
The 4K single fiber optic output transmits up
to 3840x2160 progressive, 59.94 frames
per second video. The data is sent via a
single fiber by Wavelength Division
Multiplexing (WDM) the four 1920x1080
quadrants of the 3840x2160 video via
SMPTE
ST
424 Compliant 3G-SDI.
The optical output conforms to the IEC
60825-1 Classification, the “Eye Safe”
certification for laser transmission
equipment.
Please contact AltaSens for further
information and for assistance to identify or
purchase compatible equipment that will
work with this single fiber 4K optical format.
WRITE-PROTECT SWITCH
WRITE/DELETE ENABLED
WRITE/DELETE DISABLED
The ProCam UHD has a single fiber optic and
a HD-SDI monitor output. Connect an
appropriate device to each output, observing
the following specifications:
HD-SDI Monitor Output
Write-Protect Switch on the SD Card
Control
Connector
Inputs
The ProCam UHD features a multi-function
control input on the 9-pin D-sub connector.
This connector contains several features,
including serial communication to and from
the camera for external control, genlock
input, and 12-15 V output to power external
controllers. The Control connector’s pinout is
shown below
5
1
9
6
The HD-SDI monitor output is 1920x1080,
interlaced. The frame rate is dependent upon
the frequency of main output.
Note:
Test pattern output for this unit is
currently only available in single fiber
optic output at this time. HD-SDI monitor
output is not available.
Use cable at a length of < 100 meters
Not guaranteed to connect to all
appliances
Caution
:
The controller which ProCam UHD will
provide power supply is limited to below
1A.
PIN DIRECTION DESCRIPTION
1
―
Not Used
2
OUT
Data from Camera
3
IN
Serial Data to Camera
4
―
Not Used
5
―
Ground
6
IN
Genlock
Sync Signal
7
―
Not Used
8
―
Ground
9
OUT
12-15 Volts
D-SUB
9
FEMALE
CONNECTOR
ON
BACK
OF
CAMERA
CAPACITY
QUICK
TIME
4K
16 GB
(UHS
SPEED
CLASS
3)
12 min
32 GB
(UHS
SPEED
CLASS
3)
25 min
64 GB
(UHS
SPEED
CLASS
3)
50 min
128 GB
(UHS
SPEED
CLASS
3)
100 min
16
Estimated Recordable Time of SD
Cards
The estimated recordable time is only a
guide. Differences may occur depending on
the SD card in use and the battery condition.
Slide the write-protect switch upward to
enable writing or deleting.
Slide the write-protect switch downward to
prevent writing or deleting. (Images in the
card are protected)
Video
Outputs
4K Single Fiber Optic Output
The 4K single fiber optic output transmits up
to 3840x2160 progressive, 59.94 frames
per second video. The data is sent via a
single fiber by Wavelength Division
Multiplexing (WDM) the four 1920x1080
quadrants of the 3840x2160 video via
SMPTE
ST
424 Compliant 3G-SDI.
The optical output conforms to the IEC
60825-1 Classification, the “Eye Safe”
certification for laser transmission
equipment.
Please contact AltaSens for further
information and for assistance to identify or
purchase compatible equipment that will
work with this single fiber 4K optical format.
WRITE-PROTECT SWITCH
WRITE/DELETE ENABLED
WRITE/DELETE DISABLED
The ProCam UHD has a single fiber optic and
a HD-SDI monitor output. Connect an
appropriate device to each output, observing
the following specifications:
HD-SDI Monitor Output
Write-Protect Switch on the SD Card
Control
Connector
Inputs
The ProCam UHD features a multi-function
control input on the 9-pin D-sub connector.
This connector contains several features,
including serial communication to and from
the camera for external control, genlock
input, and 12-15 V output to power external
controllers. The Control connector’s pinout is
shown below
5
1
9
6
The HD-SDI monitor output is 1920x1080,
interlaced. The frame rate is dependent upon
the frequency of main output.
Note:
Test pattern output for this unit is
currently only available in single fiber
optic output at this time. HD-SDI monitor
output is not available.
Use cable at a length of < 100 meters
Not guaranteed to connect to all
appliances
Caution
:
The controller which ProCam UHD will
provide power supply is limited to below
1A.
PIN DIRECTION DESCRIPTION
1
―
Not Used
2
OUT
Data from Camera
3
IN
Serial Data to Camera
4
―
Not Used
5
―
Ground
6
IN
Genlock
Sync Signal
7
―
Not Used
8
―
Ground
9
OUT
12-15 Volts
D-SUB
9
FEMALE
CONNECTOR
ON
BACK
OF
CAMERA
CAPACITY
QUICK
TIME
4K
16 GB
(UHS
SPEED
CLASS
3)
12 min
32 GB
(UHS
SPEED
CLASS
3)
25 min
64 GB
(UHS
SPEED
CLASS
3)
50 min
128 GB
(UHS
SPEED
CLASS
3)
100 min
16
■
Formatting Tool
To format SD cards for recording,
we recommend to use the tool below;
SD Association
SD Card Fromatter 4.0 for SD/SDHC/SDXC
URL : https://www.sdcard.org/downloads/
formatter_4/index.html
Caution:
●
Do not use the Windows default
formatting tool.
Video Outputs
The 4K Camera Module has quad SDI and
a HD-SDI monitor output. Connect an
appropriate device to each output, observing
the following specifications:
■
HD-SDI Monitor Output
The HD-SDI monitor output is 1920x1080,
interlaced. The frame rate is dependent
upon the frequency of main output.
■
4K Quad SDI Output
The 4K quad SDI output transmits up to
3840x2160 progressive, 59.94 frames
per second video. The data is sent via
Quad SDI by square division the four
1920x1080 quadrants of the 3840x2160
video via SMPTE ST424 Compliant
3G-SDI.
Note:
●
Use cable at a length of < 100 meters.
●
Not guaranteed to connect to all
appliances.