8
7
Rear panel
Daily Operations / Connections (cont.)
CAUTION
Do not connect the power cord until all other
connections are completed.
1
POWER switch
Turns the AC power on or off.
• You need to press
button on the front
panel to turn on the monitor after turning on the
POWER switch.
2
AC IN terminal
AC power input connector.
• Connect the provided AC power cord to an AC
outlet.
• Attach the provided power cord holder to prevent
accidental disconnection of the AC power cord (
☞
page 9).
3
DC switch
Turns the DC 12 V power on or off.
• You need to press
button on the front panel
to turn on the monitor after turning on the DC
switch.
• The monitor consumes the battery even while the
monitor is on standby. To save battery life, turn off
the DC switch.
4
DC IN 12V terminal
DC 12 V (maximum
DC 17 V) power input
connector.
• While using both the AC and DC 12 V power
supply, AC power supply is preferentially used. If
the AC power supply is cut off (for example, when
unplugging the AC power cord), the power supply
automatically switches to the DC 12 V power
supply.
5
VIDEO/COMPONENT terminals (BNC)
IN:
Input terminals for the composite (VBS) and the
analog component (Y/P
B
/P
R
) signals.
• Select the signal type in “VIDEO/COMPO. SEL.”
corresponding to the type of the input signal (
☞
page 10).
OUT:
Output terminal for the composite (VBS) and
the analog component (Y) signals.
6
AUDIO terminal (pin jack)
IN:
Input terminal for the analog audio signals.
• Use this terminal for the analog audio connection
of the SDI.
OUT:
Output terminal for the analog audio signals
to the AUDIO IN terminal.
7
E. AUDIO HD/SD SDI terminal (BNC)
IN:
Input terminal for the HD/SD SDI signals.
• The terminals accept also EMBEDDED AUDIO
signals* including up to 12 audio channels with
the sampling frequency of 48 kHz.
OUT:
Output terminal for the HD/SD SDI signals.
• The signals are re-clocked, then emitted from this
terminal.
• The signals are emitted only when the monitor is
on or in P.SAVE (power save) mode.
8
REMOTE terminal
Terminal for controlling the monitor by an external
control.
☞
“External Control” on page 14
9
Carry handle
Use this handle when carrying the monitor.
p
Security slot
Install a security wire to this slot.
q
Screw holes for external battery attachment
Attach external battery for DC 12 V power supply
by using 2 screw holes. Choose the appropriate
screw holes from 1, 2, 3 or 4, according to the type
of external battery.
• Use the Anton Bauer Dionic 90 (mount: QR DXC-
M3A) external battery.
CAUTION
• Do not use the external battery for DC 24 V power
supply.
• Use only the battery specified above. If a heavy
battery is used, it may fall off depending on the way
the monitor is used.
* Using the audio level meter
You can check the conditions of the current
EMBEDDED AUDIO signals in the audio level meter.
The setting for the level meter is selected in “AUDIO
SETTING” (
☞
page 11).
Note for connections
• Before making any connections, turn off all the equipment.
• Use a cord whose plugs correctly match the terminals on this monitor
and the equipment.
• Plugs should be firmly inserted; poor connections could cause noise.
• When unplugging a cord, be sure to grasp its plug and pull it out.
• DO NOT connect the power cord until all connections are completed.
• Refer also to the user manual of each piece of equipment.
When using DC 12 V power (maximum DC
17 V), check the DC IN 12V terminal pin signal,
and use the correct polarity. If the polarity is
reversed, this could cause a fire or personal
injury.
DT-V9L1D_EA_EN_R.indd 8
DT-V9L1D_EA_EN_R.indd 8
07.9.14 6:19:21 PM
07.9.14 6:19:21 PM
