JVC DT-V1710CG Скачать руководство пользователя страница 72

Страница: 72 / 76

1-72 (No. 52152)

BRIGHTNESS ADJUSTMENTS (NTSC/PAL Y/C)

Measuring Instruments

Signal generator (Gray scale signal)

Card (Slot)

NTSC/PAL Video Input Card (Slot 2)

Test Points

Adjustment Points

S*02 (4:3 Overscan Bright High), S*06 (4:3 Overscan Bright Low),
SP** (4:3 Underscan Bright High/Low),
SQ** (16:9 Overscan/Underscan Bright High/Low) [Service Menu]

Notes:

•

Ensure that the output waveforms from the NTSC/PAL Video Input Cards
are normal before proceeding to the following adjustments.

•

Perform the following adjustments after completing the 1080/60i Brightness
Adjustment.

•

Set the PICTURE SUB ADJ. data in the Setup Menu to “00”.

•

The SR value (see the description for the HDTV Brightness adjustment)
becomes the reference value for the following adjustments. When this data

is changed, it is required to re-adjust the data of all of the adjustment signals

(HDTV, SDTV and NTSC/PAL).

When re-adjusting the 1080/60i signal, use the SI. (For the adjustment of

the 1080/60i signal, use the Component/RGB Input Card.)

•

When overscan data of a signal is changed, it is required to re-adjust the
underscan data of the same adjustment signal.

•

When the 4:3 data of a signal is changed, it is required to re-adjust the 16:9
data of the same adjustment signal.

•

After completing the brightness adjustments, make sure that the Low-Light is
not deviated. If it is, it is required to perform the Low-Light adjustment again.

0% Black area

2 4 6 8 10 1214 0

2 4 6 8 10 1214

<White Balance HIGH: D9300>

(1) Apply the NTSC gray scale signal to INPUT D (Terminal Y/

C of the NTSC/PAL Video Input Card).

(2) Set “COLOR TEMP.” of COLOR TEMP./BAL. in the Setup

Menu to HIGH.

(3) Set the PHASE, CHROMA, BRIGHT and CONTRAST

potentiometers on the front panel to the center click positions.

(4) Adjust

SB02

in the Service Menu so that the 0% black area

in the gray scale signal lights up slightly. (Be sure to avoid
degradation of the black color.)

(5) Set the ASPECT button on the front panel to ON so that the

scanning size is 16:9.

(6) Adjust

SQ08

so that the 0% black area in the gray scale

signal lights slightly. (Be sure to avoid degradation of the
black color.)

(7) Set the ASPECT button on the front panel to OFF and the

UNDER SCAN button to ON to set the scanning size to
underscanning for the 4:3 ratio.

(8) Adjust

SP05

so that the 0% black area in the gray scale

signal lights up slightly. (Be sure to avoid degradation of the
black color.)

(9) Set the ASPECT button on the front panel to ON to set the

scanning size to underscanning for the 16:9 ratio.

(10)Adjust

SQ11

so that the 0% black area in the gray scale

signal lights slightly. (Be sure to avoid degradation of the
black color.)

(11) Set the ASPECT and UNDER SCAN buttons on the front

panel to OFF.

<White Balance LOW: D65>

(12)Set “COLOR TEMP.” of COLOR TEMP./BAL. in the Setup

Menu to LOW.

(13)Adjust

SB06

so that the 0% black area in the gray scale

signal lights slightly. (Be sure to avoid degradation of the
black color.)

(14)Set the ASPECT button on the front panel to ON so that the

scanning size is 16:9.

(15)Adjust

SQ09

so that the 0% black area in the gray scale

signal lights slightly. (Be sure to avoid degradation of the
black color.)

(16)Set the ASPECT button on the front panel to OFF and the

UNDER SCAN button to ON to set the scanning size to
underscanning for the 4:3 ratio.

(17)Adjust

SP06

so that the 0% black area in the gray scale

signal lights slightly. (Be sure to avoid degradation of the
black color.)

(18)Set the ASPECT button on the front panel to ON to set the

scanning size to underscanning for the 16:9 ratio.

(19)Adjust

SQ12

so that the 0% black area in the gray scale

signal lights slightly. (Be sure to avoid degradation of the
black color.)

(20)Set the ASPECT and UNDER SCAN buttons on the front

panel to OFF.

(21)Vary the adjustment signal and adjustment data, and re-

perform adjustments in steps 1 to 20 above (see Table 24).

Adjustment

White Balance HIGH

White Balance LOW

Signal

Overscan

Underscan

Overscan

Underscan

4 : 3

16 : 9

4 : 3

16 : 9

4 : 3

16 : 9

4 : 3

16 : 9

NTSC(Y/C)

SB02

SQ08

SP05

SQ11

SB06

SQ09

SP06

SQ12

PAL(Y/C)

SD02

SQ20

SP11

SQ23

SD06

SQ21

SP12

SQ24

Table 24

Содержание DT-V1710CG













































































Результаты поиска

Содержание DT-V1710CG

Отзывы:

JVC DT-V1710CG, Руководство по обслуживанию, Страница: 72 / 76

Результаты поиска

Содержание DT-V1710CG

Отзывы: