JVC DT-V1710CG Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 76

JVC DT-V1710CG Скачать руководство пользователя страница 44

1-44 (No. 52152)

X-RAY PROTECTOR ADJUSTMENT/CHECK

Measuring Instruments

Signal generator (All-white signal)
High-voltage voltmeter
DC voltmeter

Card (Slot)

Component/RGB Input Card (Slot 1)

Test Points

Anode of CRT
TP-XR, TP-GND [S. CORRECTION PWB]

Adjustment Points

VR501 (X-Ray Protector Adjustment VR) [S. CORRECTION PWB]
VR502 (High-Voltage VR) [S. CORRECTION PWB]

Note: Perform the following adjustment after completing the Screen Voltage Coarse adjustment.

(1) Turn the

VR502

fully clockwise (the minimum position).

(2) Turn the

VR501

fully counterclockwise (the minimum position).

(3) Set the CONTRAST and BRIGHT potentiometers on the front panel to the fully clockwise positions.
(4) Connect the high-voltage voltmeter to the anode of the CRT and turn the unit ON.
(5) Apply the 1080/60i all-white signal to INPUT A (Terminal Y on the Component/RGB Input Card).
(6) Turn the

VR502

slowly counterclockwise until the value of the high-voltage voltmeter is

27.0 kV ± 0.2 kV

.

(7) Connect the DC voltmeter across TP-XR and TP-GND.
(8) Turn the

VR501

clockwise until the voltmeter reading is

5.5 V

.

(9) Turn the

VR501

slowly clockwise until the point at which the X-ray protector starts operation.

(The power turns off at the first operation and then turns on again 5 seconds later. At the second operation, the power turns off
and the LED of the INPUT SELECT D of the front panel blinks. When two operations are done consecutively, it stops at the
stand-by position.)

(10)Turn the

VR502

slightly clockwise and turn the unit ON again.

(11) Turn the

VR502

slowly counterclockwise and check the point at which the X-ray protector starts to operate.

Check that the high-voltage voltmeter value at which the X-ray protector starts to operate, is

27.0 kV ± 0.2 kV

.

(12)Apply adhesive for fixing the

VR501

in the adjusted position.

(13)Set the CONTRAST and BRIGHT potentiometers on the front panel to the center click positions.
(14)Turn the

VR502

fully clockwise (the minimum position).

4.10.3 X-RAY PROTECTOR ADJUSTMENT/CHECK

S. CORRECTION PWB

MAIN PWB

Front side

TP-XR

TP-G

Front side

(Min)

(Max)

(Min)

(Max)

VR505 [CONV_V]

VR504 [CONV_H]

VR502 [H.VOLTAGE]

VR501 [X-RAY]

CN0RD

CN00R

(Top surface view of the S. CORRECTION PWB)

VR505

VR504

VR502

VR501

CN0RD

CN00R

VR502

VR501

«
...
42
43
44
45
46
...
»

Содержание DT-V1710CG













































































Отзывы:

Нет отзывов