JVC DR-MV5SE, Инструкция по эксплуатации

Страница: 80 / 100

Filename [MV5S_13Subsidiary.fm]
Masterpage:Left+
80
EN
SUBSIDIARY SETTINGS
Page 80Wednesday, 8 June 2005 11:05
OTHERS
8
AUTO TIMER — OFF / ON
This is the setting for engaging timer recording standby mode.
OFF
: Press TIMER
#
engage timer recording standby mode.
ON
: Timer recording standby mode is automatically engaged when
the unit is turned off.
8
RESUME — OFF / ON / DISC RESUME
When this function is set to “ON” or “DISC RESUME”, you can use
the resume function. (
墌
pg. 48)
OFF
: You cannot use the resume function.
ON
: You can start playback from the resume point of the placed
disc.
DISC RESUME
: The unit retains a memory of the resume points of
the last 30 discs played back, even though they have been ejected.
NOTE:
“DISC RESUME” setting works on DVD VIDEO, VCD and already
finalised DVD-R/DVD-RW (video mode) discs. For other types of discs,
the function under “ON” setting will be applied even if “RESUME” is set
to “DISC RESUME”.
If you connect the unit and TV with Component Video Connection
(
墌
pg. 15), you can select the scan mode from two modes:
Interlaced scan mode which is used in the conventional TV
system, and Progressive scan mode which enables reproduction of
higher-quality images.
8
Interlaced scan
In the conventional video system, a picture is shown on the display
monitor in two halves. The Interlaced scan system places lines of
the second half of the picture in-between lines of the first half of the
picture.
8
Progressive scan
Progressive scan displays all the horizontal lines of a picture at one
time, as a single frame. This system can convert the interlaced
video from DVD into progressive format for connection to a
progressive display. It dramatically increases the vertical
resolution.
1
Press DVD so that the DVD lamp lights up on the unit.
2
Press PROGRESSIVE SCAN for 3 or more seconds.
●
Video output indicator ( ) lights on the front display panel if
Progressive scan mode has been established. (
墌
pg. 14)
●
Each press of PROGRESSIVE SCAN for 3 or more seconds
switches the scan mode.
NOTES:
●
When the progressive mode is set, be sure to set “L-1 OUTPUT” to
“COMPONENT”. (
墌
pg. 44) Progressive scan is output only from
[COMPONENT VIDEO OUT] connector.
●
Interlaced scan mode is the setting at your purchase.
●
Interlaced scan mode might be suitable depending on video material.
●
Scan mode cannot be set while menu screen is displayed.
●
When the Progressive scan mode is engaged, no video signal is
output from [L-1 IN/OUT] connector.
Scan Mode Set
ATTENTION:
●
Your TV needs to be compatible with Progressive.
●
Make sure that there is no disc in the unit.
●
Turn on the unit.
●
Turn on the TV and select the AV mode.
●
Slide the TV/DVD switch to DVD .
Watch the images on VHS deck in the Progressive scan
mode via component video
1
Set the Progressive-compatible TV to the component input
mode.
2
Press DVD so that the DVD lamp lights up on the unit.
3
Press PROGRESSIVE SCAN for 3 or more seconds.
●
The video output indicator lights up on the front display panel.
4
Press VHS so that the VHS lamp lights up on the unit, then
press PROGRESSIVE SCAN .
●
“
]
” lights up on the unit.
NOTES:
●
Be sure to engage the DVD deck in stop mode.
●
During still picture in VHS Progressive Scan mode, the images
may jitter, but this is not a malfunction.
DVD
VHS
PROGRESSIVE
SCAN
MV5S_13Subsidiary.fm Page 80 Wednesday, June 8, 2005 11:05 AM