JVC AV-N29304 Скачать руководство пользователя

Страница: 18 / 26

AV-N29304
AV-N29430

1-18 (No.52129)

3.6 ADJUSTMENT PROCEDURE
3.6.1 CHECK ITEM

3.6.2 VCO

3.6.3 RF AGC

3.6.4 ADJUSTMENT OF FOCUS

Item

Measuring

instrument

Test point

Adjustment part

Description

B1 POWER
SUPPLY

DC voltmeter

Signal
generator

B1 Connector
1-pin : TP-91
3-pin : TP-E
[MAIN PWB]

(1) Receive the black-and-white signal. (color off)
(2) Connect the DC voltmeter to TP-91 (B1 connector 1

pin) and TP-E (B1 connector 3 pin).

(3) Confirm that the voltage is DC134V

2V.

Item

Measuring

instrument

Test point

Adjustment part

Description

IF VCO

Remote
control unit

[9.VCO]

CW transf. (T111)
[MAIN PWB]

• It must not adjust without inputting the RF signal.

(1) Receive a broadcast.
(2) Select 9.VCO mode from the SERVICE MENU.
(3) Change the [AFC] to OFF and [FINE] to 0.
(4) Confirm that the color change from "TOO HIGH" to

"TOO LOW" by CW transf. on MAIN PWB, and
check the [SYNC] is YES.

(5) Adjust CW transf. until "GOOD" letters turns green.

And then confirm that the [SYNC] is YES again.
Adjustment can be done in this statement.

(6) It return the [AFC] to ON.
(7) Push the [EXIT] key to exit the [9.VCO] mode.

TOO HIGH GOOD TOO LOW

SYNC: YES
AFC ON
FINE 0

Item

Measuring

instrument

Test point

Adjustment part

Description

RF AGC

Signal
generator

Remote
control unit

[1.V/C(S)]
S21 : AGC ADJ

(1) Receive a black-and-white signal (colour off).
(2) Select <S21>(AGC ADJ) of the 1.V/C(S).
(3) Press the [MUTING] key and turn the picture color

off.

(4) With the [VOLUME (-)] key to get the noise in the

screen picture (zero side of setting value).

(5) Press the [VOLUME (+)] key several times and step

when noise disappears from the screen (at that time,
not to increase the value too much).

(6) Change to other channels and make sure that there

is no irregularity.

(7) Press the [MUTING] key and get color out.

No.

S21

Setting item

AGC ADJ

㨪

127

Variable

range

Initial setting

value

Item

Measuring

instrument

Test point

Adjustment part

Description

FOCUS

Signal
generator

FOCUS VR
[In HVT]

(1) Receive the crosshatch signal.
(2) While looking at the screen, adjust the FOCUS VR

to the vertical and horizontal lines will be clear and in
fine detail.

(3) Make sure that the picture is in focus even when the

screen gets darkened.

Содержание AV-N29304



























Результаты поиска

Содержание AV-N29304

Отзывы:

Похожие инструкции для AV-N29304

Бренды по названию

Популярные бренды

JVC AV-N29304, Руководство по обслуживанию

Результаты поиска

Содержание AV-N29304

Отзывы:

Похожие инструкции для AV-N29304

Бренды по названию

Популярные бренды