JVC AV-28RT4BU, Инструкция по эксплуатации

Страница: 11 / 16

- 10 -
&28175<
&217,18(
8.
:$51,1*
$//35(6725('352*5$00(6
:,//%((5$6('
• If you do not want to start A.P.S. , you can cancel it by press-
ing the Menu button on your remote control.
• First select your country by pressing “ ” or “ ” button.
This will affect the sort process in APS.
• To select “
Continue ” use “ ” or “ ” button. By pressing
“ ” or “ ” button start the A.P.S.
• When you start A.P.S. the following window will appear on
the screen.
35&+$11(/1$0(
&&
$36,65811,1*
3/($6(:$,7
$36
After APS is finalized, a programme list will appear on the
screen. In the programme list you will see the programme
numbers and names assigned to the programmes.
If you do not accept the locations and / or the programme
names of programmes, you can change them in Programme
menu.
Other Features
TV Status
Programme Number , Programme Name (or EXT ), (they
are displayed on the upper left of the screen). The sound indi-
cator is displayed with them too. They are displayed after
programme change for 3 seconds.
Sound Indicator
The alternatives of the indicator are Mono, Stereo, Dual I and
Dual II. This indicator is displayed under the programme num-
ber indicator on the screen.
0212
In Mono broadcast or in forced-mono (for stereo broadcast).
67(5(2
In Stereo broadcast.
'8$/ , ²
If dual broadcast detected. Dual I is selected in default and
also can be selected after Dual II by Remote Control.
'8$/ ,, ²
If Dual II is selected by Remote Control.
Mute Indicator
It is placed in the upper middle of the screen when enabled,
and it stays there until it is disabled.
To cancel mute, there are two alternatives; the first one is by
pressing the “ ” button, this volume is set to the preceding
value, and the second one is increasing or decreasing the
volume level.
No-Signal Detection (TV mode)
If no valid signal is detected, it takes 5 minutes to switch to
the Stand-By mode unless any signal detected or any Re-
mote Control command is accessed.
After a Remote Control command (if No-Signal Timer is active)
the timer stops and if no signal detected again the timer is
initialized to 5 minutes and starts 3 seconds later again to
count down.
It is not valid in EXT modes.
Volume Bar
It is displayed in the lower middle of the screen. When a vol-
ume command is received (pressing “ +” or “ -” by
Remote Control or Control panel at the right side of the TV)
and no menu is active, it stays on the screen for 3 seconds,
after the last volume command or until another command is
received in between.
EXT Modes
By pressing the “ AV ” button you can switch your TV to EXT
modes (except being in Teletext). Pressing this button con-
secutively will switch the TV in one of the optional EXT modes:
EXT1, EXT2, EXT2 S and EXT3
In order to quit the EXT mode press any digit buttons or “ ”
/ “ ”.
Picture Mode
You can change Picture Mode settings by pressing “ STAN-
DARD ” button when no menu appears.
Zoom Modes
Zoom mode can be changed by pressing Red button. You can
change the screen size according to the picture aspect ratio.
Select the optimum one from the following ZOOM modes: Auto ,
4:3 and 16:9 .
VCR Control Buttons
The buttons can be used to operate a JVC brand VCR. Press-
ing the button having the same appearance as the original
remote control button of a device makes the function work in
the same way as the original remote control.
Press the VCR Control Button to control your VCR.
Note:
• If your device is not made by JVC, these buttons cannot be
used.
• Even if your device is made by JVC, some of these buttons
or any one of the buttons may not work, depending on the
device.
• You can use the / buttons to choose a TV channel
which the VCR will receive.
C01-ENG&BG-AK49-C1100UK-2834-CLED-PLLCH-(AV-28RT4BU&SU)-10041581-5008xxxx.p65 14.06.2006, 11:43 10