17
USING THE REMOTE CONTROL UNIT
The Remote Control Unit can operate this
camcorder from a distance as well as the basic
operations (Playback, Stop, Pause, Fast-Forward
and Rewind) of your VCR. Make sure the remote
control is pointed at the remote sensor.
To magnify the recorded image up to 10X at any
time during playback. Make sure that the TBC
mode is activated.
1)
Press PLAY to find the scene of interest.
2)
Press ZOOM (
T/W
). Pressing
T
zooms in. To
end zoom press and hold
W
until magnification
returns to normal. Or, press STOP and then
press PLAY.
• Due to digital image processing, the quality of
the image may suffer.
The remote control lets you set/release interval
time and recording time without setting REC
TIME/INT. TIME (
pg. 15) in SYSTEM MENU.
Animation
Each time ANIM. is pressed, the recording time
changes in the following order: 1/4S, 1/2S, 1S, 5S
and no indication (off).
Time-Lapse
Each time REC TIME is pressed, the recording
time changes in the following order: 1/4S, 1/2S,
1S, 5S and no indication (off). Each time INT.
TIME is pressed, the interval time changes in the
following order: 15S, 30S, 1MIN, 5MIN and no
indication (off).
You can record a new scene onto a previously
recorded tape. Only the video signal is recorded
in this mode.
1)
Set the Power Switch
$
to “PLAY” while
pressing down the Lock Button
#
located on
the switch.
2)
Play back the tape, locate the edit-out point
and press PAUSE . Perform steps
2)
through
5)
of “COUNTER MEMORY” (
pg. 16)
3)
Press REW to go a little beyond the beginning
of the scene you want to replace, press PLAY
to view the recorded tape, and press PAUSE
exactly at the edit-in point where the new
scene should start.
4)
While holding down INSERT, press and
release PAUSE.
4
appears.
5)
To begin Insert Editing, press START/STOP.
When the counter reaches “0:00:00”, editing
stops automatically and the camcorder enters
the Insert-Pause mode. To end Insert Editing,
press STOP.
• During Insert Editing, the original audio will be
heard from the speaker.
• After step
4)
, “Retake” (
pg. 10) can be
performed.
• The tape may stop slightly before or after the
designated end point, and noise bars may
appear. Neither indicates a defect in the unit.
You can record a new soundtrack on a
prerecorded tape (normal audio only). The sound
is recorded from the built-in microphone.
Perform steps
1)
and
2)
of the Insert Editing
procedure.
1)
Press REW to go a little beyond the beginning
of the scene onto which you want to dub the
new audio, press PLAY to view the recorded
tape, then press PAUSE at exactly the point
where dubbing should start.
2)
While holding down A. DUB, press and release
PAUSE.
3)
To begin Audio Dubbing, press PLAY. When
the counter reaches “0:00:00”, Audio Dubbing
stops automatically and the camcorder enters
the Audio Dub-Standby mode. To end Audio
Dubbing, press STOP.
• Do not press REW or FF during Audio Dub-
Standby, or the edit points will not be accurate.
• If the microphone is too close to the TV, or if
the TV’s volume is too high, whistling or
howling may occur.
• Insert Editing and Audio Dubbing may not work
correctly if the tape contains blank segments,
or if the recording speed was changed during
the original recording.
• To edit/dub onto a tape, make sure the erase
protection tab is in the position that allows
recording.
• Do not press STOP during Insert Editing or
Audio Dubbing, or the edit points will not be
accurate.
USING THE REMOTE CONTROL UNIT (GR-SXM301/265AS only)
Playback Zoom (GR-SXM301AS only)
Animation And Time-Lapse
Insert Editing
T
W
START/
STOP
REW
PLAY
FF
INSERT
A.DUB
REC TIME
INT. TIME
ANIM.
SELF TIMER
TIME LAPSE
STOP
PAUSE
ZOOM (T/W)
PLAY
REW
STOP
INSERT
REC TIME/
ANIM.
START/STOP
FF
PAUSE
A.DUB
INT. TIME
Audio Dubbing
For Insert Editing/Audio Dubbing
GR-SXM301AS-EN.fm Page 17 Monday, December 6, 2004 8:28 PM
