ENGLISH
21
Data Size:
B6L (182 mm x 128 mm)
Book Size:
B6L (182 mm x 128 mm)
[BASS BOOST]
[LV1]
to
[LV5]
: Selects your preferred bass boost level. ;
[OFF]
: Cancels.
[LOUDNESS]
[LV1]
/
[LV2]
: Selects your preferred low or high frequencies boost to
produce a well-balanced sound at low volume. ;
[OFF]
: Cancels.
[SUBWOOFER SET]
[ON]
: Turns on the subwoofer output. ;
[OFF]
: Cancels.
[FADER]
(Not applicable if 3-way crossover is selected.) (Page 7)
[R15]
to
[F15]
(
[0]
): Adjusts the front and rear speaker output balance.
[BALANCE]
[L15]
to
[R15]
(
[0]
): Adjusts the left and right speaker output balance.
[VOLUME OFFSET]
[–15]
to
[+6]
(
[0]
): Presets the initial volume level of each source by
comparing to the FM volume level.
(Before adjustment, select the source you want to adjust.)
[SOUND EFFECT]
[SOUND RECNSTR]
(Sound
reconstruction)
(Not applicable for RADIO source and AUX source.)
[ON]
: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression. ;
[OFF]
: Cancels.
[SPACE ENHANCE]
(Not applicable for RADIO source.)
[SML]
/
[MED]
/
[LRG]
: Virtually enhances the sound space. ;
[OFF]
: Cancels.
[SND REALIZER]
[LV1]
/
[LV2]
/
[LV3]
: Virtually makes the sound more realistic. ;
[OFF]
: Cancels.
[STAGE EQ]
[LOW]
/
[MID]
/
[HI]
: Virtually adjusts the sound position heard from the
speakers. ;
[OFF]
: Cancels.
[DRIVE EQ]
[ON]
: Boosts the frequency to reduce the noise heard from outside the
car or running noise of the tyres. ;
[OFF]
: Cancels.
[SPEAKER SIZE]
Depending on the crossover type you have selected (see “Change the
crossover type” on page 7), 2-way crossover or 3-way crossover
setting items will be shown. (See the following “Crossover settings”.)
By default, 2-way crossover type is selected.
[X ‘ OVER]
Audio Settings
[DTA SETTINGS]
For settings, see “Digital Time Alignment settings” on page 23.
[CAR SETTINGS]
•
: For 2-way crossover:
[SUB-W LEVEL]
/
[SUBWOOFER SET]
is
selectable only if
[SWITCH PREOUT]
is set to
[SUB-W]
. (Page 6)
•
[SUB-W LEVEL]
is selectable only when
[SUBWOOFER SET]
is set to
[ON]
.
Crossover settings
Below are the available setting items for 2-way crossover and 3-way
crossover.
SPEAKER SIZE
Selects according to the connected speaker size for optimum performance.
• The frequency and slope settings are automatically set for the crossover of
the selected speaker.
• If
[NONE]
is selected for the following speaker in
[SPEAKER SIZE]
, the
[X ‘ OVER]
setting of the selected speaker is not available.
–
2-way
crossover:
[TWEETER]
of
[FRONT]
/
[REAR]
/
[SUBWOOFER]
–
3-way
crossover:
[WOOFER]
X ‘ OVER (crossover)
•
[FRQ]
/
[F-HPF FRQ]
/
[R-HPF FRQ]
/
[SW LPF FRQ]
/
[HPF FRQ]
/
[LPF FRQ]
: Adjusts the
crossover frequency for the selected speakers (high pass filter or low pass
filter).
If
[THROUGH]
is selected, all signals are sent to the selected speakers.
•
[SLOPE]
/
[F-HPF SLOPE]
/
[R-HPF SLOPE]
/
[SW LPF SLOPE]
/
[HPF SLOPE]
/
[LPF SLOPE]
:
Adjusts the crossover slope.
Selectable only if a setting other than
[THROUGH]
is selected for the
crossover frequency.
•
[SW LPF PHASE]
/
[PHASE]
: Selects the phase of the speaker output to be in line
with the other speaker output.
•
[GAIN LEFT]
/
[GAIN RIGHT]
/
[F-HPF GAIN]
/
[R-HPF GAIN]
/
[SW LPF GAIN]
/
[GAIN]
: Adjusts
the output volume of the selected speaker.
KMM_BT408_MN_B5A-3850-00_EN.indd 21
KMM_BT408_MN_B5A-3850-00_EN.indd 21
1/27/2022 12:15:22 PM
1/27/2022 12:15:22 PM
