Juniper SRX340 Скачать руководство пользователя страница 70

Страница: 70 / 150

Figure 7: Installing the Rack Mount Brackets (Center Mount Position)

Have one person grasp the sides of the services gateway, lift it, and position it in the
rack.

Align the bottom hole in each mounting bracket with a hole in each rack rail, making
sure the chassis is level.

Have a second person install a mounting screw into each of the two aligned holes.
Use a Phillips (+) screwdriver, number 2 to tighten the screws.

Install the second screw in each mounting bracket as shown in

Figure 8 on page 52

Figure 8: Installing the Services Gateway in the Rack (Front Mount Shown,
Center Mount Similar)

Verify that the mounting screws on one side of the rack are aligned with the mounting
screws on the opposite side and that the services gateway is level.

Documentation

•

Connecting the SRX340 Services Gateway Grounding Cable on page 54

•

Connecting the SRX340 Services Gateway to an AC Power Supply on page 59

SRX340 Services Gateway Hardware Guide

Содержание SRX340

























































































































Результаты поиска

Содержание SRX340

Отзывы:

Похожие инструкции для SRX340

Бренды по названию

Популярные бренды

Juniper SRX340, Руководство по оборудованию

Результаты поиска

Содержание SRX340

Отзывы:

Похожие инструкции для SRX340

Бренды по названию

Популярные бренды